View Profile: Mark413 - DMCTalk Forum

Yesterday, 07:12 PM

DMC-81 replied to a thread 2 consecutive number VIN Deloreans for sale in General DeLorean Discussion

I don't see the typical eyebrow problem. The fascia is sagging in the middle. Because this is the parts car, most likely the Front Facia...

31 replies | 1009 view(s)

02-23-2021, 07:54 PM

Bitsyncmaster replied to a thread [General] Owners manual, doors up driving? in General DeLorean Discussion

I think most of us that have been in a parade drive it with the doors open. So a paved road at 5 MPH is probably safe.

40 replies | 1020 view(s)

02-22-2021, 09:25 AM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Like always the photo just can not get the true colors of LEDs. I do see I need to fix the small green dot above and to the right of "MAX". I also...

169 replies | 20318 view(s)

02-21-2021, 05:59 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

So what kind of plastic do you think the OEM faceplate was made of? I just ordered some ABS filament to try another HVAC face plate made with that. ...

169 replies | 20318 view(s)

02-21-2021, 03:43 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Alignment cylinders worked out perfect. These are 1.416" dia. which makes it snug on the DMCH decal. My printed faceplate I made the holes 0.010...

169 replies | 20318 view(s)

02-18-2021, 10:15 AM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Trying to get something engineered so I can place the decal exactly in the correct position. I can only think of using the two push button holes for...

169 replies | 20318 view(s)

02-17-2021, 07:57 PM

Bitsyncmaster replied to a thread [Fuel] Tank varnish in General DeLorean Discussion

You won't be able to buy acetone in California.

20 replies | 566 view(s)

02-17-2021, 07:03 PM

Bitsyncmaster replied to a thread [General] New Door Lock ECU in Custom DeLoreans/Mods

Yes the OEM pins are not really interchangeable with the AMP connector. My pin extractor does not work with the AMP pins.

56 replies | 5203 view(s)

02-17-2021, 06:59 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Well I'm going with the idea to print the HVAC in black and have made cutouts for the decal illumination areas. It would probably work without...

169 replies | 20318 view(s)

02-16-2021, 04:48 PM

Bitsyncmaster replied to a thread [Suspension] New Delorean bushings: size discrepancy in General DeLorean Discussion

It looks like only 0.028" difference so I would think the casing is still there.

6 replies | 267 view(s)

02-14-2021, 05:56 PM

Bitsyncmaster replied to a thread [Suspension] New Delorean bushings: size discrepancy in General DeLorean Discussion

Did you check if the old one has been bent out of round. Measure it at 90 degrees from the first measurement.

6 replies | 267 view(s)

02-14-2021, 11:12 AM

Bitsyncmaster replied to a thread [General] Door locks in General DeLorean Discussion

Yes the inertia switch is what I mean. The door lock ECU is a black box (if stock) mounted on the relay compartment metal plate. It has a 9 pin...

5 replies | 237 view(s)

02-13-2021, 03:39 PM

Bitsyncmaster replied to a thread [General] Door locks in General DeLorean Discussion

If your impact sensor is triggered it will unlock if you have the door lock ECU installed.

5 replies | 237 view(s)

02-10-2021, 06:00 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

I did get that clear filament and printed an HVAC panel. Only real problem was that 0.71 deg offset from square so the two standoffs are offset to...

169 replies | 20318 view(s)

02-10-2021, 04:53 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Ran into another problem. My 4 corner standoffs, the top 2 were shifted to the right. Checked my design a 100 times and then thought to use a...

169 replies | 20318 view(s)

02-08-2021, 11:23 AM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Thanks. I plan to test to 140 F or above.

169 replies | 20318 view(s)

02-07-2021, 07:40 PM

Bitsyncmaster replied to a thread Finding cause of loss of rest pressure in General DeLorean Discussion

Here is a interesting tidbit of info. Well after about a week with it holding around 44 PSI, I released the pressure and it leaked out the gas...

18 replies | 585 view(s)

02-07-2021, 03:53 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

There is no mechanical needs for the HVAC. Just my concern is the bond between the decal and faceplate. I do plan to try PETG and ABS to play with....

169 replies | 20318 view(s)

02-07-2021, 09:25 AM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Got some black pro tough PLA from Matterhackers. Ran my test print and it worked nice. This stuff runs at 210 C and 60 C bed where as the PLA that...

169 replies | 20318 view(s)

02-06-2021, 03:17 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Learning how to get a good print. What I finally did was cut a one inch square of where my HVAC print was having problems. Then I could modify the...

169 replies | 20318 view(s)

02-05-2021, 06:13 PM

Bitsyncmaster replied to a thread [Engine] Increased idle with AC in General DeLorean Discussion

If it was just the added engine load and your idle system could not keep up that with the AC your idle would drop. So my guess is the problem is...

12 replies | 420 view(s)

02-05-2021, 06:29 AM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Well I figured it out. I had to select expert options with my slicer and set the minimum area to use infill to a very large number (100,000 mm2). I...

169 replies | 20318 view(s)

02-05-2021, 06:13 AM

Bitsyncmaster replied to a thread [Engine] Increased idle with AC in General DeLorean Discussion

My idle ECU can bump the idle speed an extra 100 RPM (with AC on) if you have it. Check if you have a blue wire coming off the idle ECU.

12 replies | 420 view(s)

02-04-2021, 05:33 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Well I still have a problem printing the HVAC. Looks like the first layer prints good at 24 mm/sec then it prints at 48 mm/sec still looking pretty...

169 replies | 20318 view(s)

02-04-2021, 05:26 PM

Bitsyncmaster replied to a thread [Suspension] Changing caster angle in General DeLorean Discussion

The sharpie test is good. I would think another test is to just sit the taper into the reamed location and measure deflection on each end. A little...

21 replies | 1005 view(s)

02-04-2021, 04:40 PM

Bitsyncmaster replied to a thread [Suspension] Changing caster angle in General DeLorean Discussion

https://www.carbideanddiamondtooling.com/Reamer.standard.ball.joint.taper.motorcycle.reamers

21 replies | 1005 view(s)

02-04-2021, 12:09 PM

Bitsyncmaster replied to a thread 3D printer in Open Discussion

Learning about this new printer. I thought setting 100% infill would stop it leaving air space inside the print, but it did not. What I think works...

169 replies | 20318 view(s)

02-04-2021, 06:37 AM

Bitsyncmaster replied to a thread Finding cause of loss of rest pressure in General DeLorean Discussion

I'm still at 43 PSI and holding many days after starting this test on my car. I thought I could also test the volume of the accumulator with this...

18 replies | 585 view(s)

Mark413
Junior Member

Mini Statistics

More 13 Friends

Mcv200

Ras12

PJK

gongloo

Bitsyncmaster

clenet

2 Groups

1981 Automatic Club

DMA

Join Groups 0 Permission Groups

Recent Visitors

Basic Information

About Mark413

Statistics

Total Posts

General Information

13 Friends

acaciolo

Bitsyncmaster

clenet

cpistocco

DannonWeb

DMC-81

gongloo

lazabby

Mcv200

MSpieler

Mark413 Junior Member

Mini Statistics

More 13 Friends

2 Groups

Join Groups 0 Permission Groups

Recent Visitors

Basic Information

About Mark413

Statistics

Total Posts

General Information

13 Friends

Mark413
Junior Member