May not have been your fault. Fuse 7 is prone to overheating.
Printable View
May not have been your fault. Fuse 7 is prone to overheating.
Well, it happened because the fuse block is poor quality, there was bad conductivity to that fuse, and the pump drew more current than it should. Same reason it happens on every car. Check your grounds and replace your fuse block... it's an incredibly important piece of proactive maintenance on every one of these cars. Unfortunately it's now become reactive repair on yours.
Hi Dave,
Sorry that fuse #7 took out your block and cover. :(.
I had fuse 10 and 11 melted in mine when I got the car, so I know what you mean. I just did the block replacement in July. I was contemplating skipping the connector replacement and just doing the plastic block, but in the end, I was very glad that I took the time to replace all of the parts in the kit, because thanks to new connectors the fuses now have a much tighter grip in the block.... just to reinforce what Jon stated.^
That said, I waited to replace the block until I verified that all electrical circuits were working, with components replaced as necessary, and grounds checked & cleaned.
In the meantime, you can install an inline fuse holder to get you back up and running. That is what the PO did, and it worked in my case until I was ready to do the replacement.
One tip if you are going to replace yours, there is an inexpensive tool to release the connectors that I wish I had known about as it would have saved me a lot of time. Someone posted about it here afterwards.
Thanks all.
After looking at many other posts online, and reading here, my gut feeling is to just replace the whole block.
I'm technical (and anal) enough to do it myself, but I'm going to see what DMC charges first.
It looks like most people who have replaced the block themselves take 3-4 hours, so my hope is that DMC can do it in 2 hours. If it's more than that, I'll do it myself.
In the event that I do it myself, I see that it's better/easier/fast to just clip the wires as close to the block as possible, and to remove the passenger seat. (Labelling is obvious)
I don't have the tools or space to remove the passenger seat, so will likely just be a contortionist for a day or two.
I'm also thinking that I'll just pull 1 wire/fuse at a time, put on the new connectors, and put it in the new block immediately, then move to the next wire/fuse.
Anything else?
I think you are underestimating how long it takes.... And in my case, there was no way to move the wires from point A to B without removing them all. The harness is too short.
You only need a 13mm socket to remove your passenger seat... If you don't have one of those, you're going to have a very tough time working on your car as about 75% of the nuts are 13mm.
Thanks jawn...
How long did it take you to replace the block, start to finish? Did you remove the seat?
It *LOOKS* like there's enough wire in the harness to pull things up, if I remove the tape and carefully pull things apart. But... I don't know actually know what I'm talking about :)
Attachment 46128
If you're willing to cut and remove everything and retape it, it may be different. I did take my seat out and it took me about 8 total hours to do the quality job that I wanted to have done in there. But I also did it before there was a how-to, and took a bunch of extra time to document everything so I could share this guide :) I also did it in like 100 degree weather which didn't help my productivity much.
YIKES!!
Yeah, it looks like DMC's new block includes labels, which is helpful. If they didn't, I'd use a labeler :)
And I want to do a quality job as well, so I'm not in a rush.
I'll call DMC on Tuesday and see what Danny says. I trust him to say "You can do it" or "Don't do it." :)
I just cut one wire off the old block at a time and installed that wire into the new block. I did pull the metal plate out to give me more room. Don't bother pulling the pins from the old block. Remember to untangle each wire as far back into the harness bundle as you can.