FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: Prv v6

    by dn010
    Replies
    6
    Views
    366

    I see you've removed your eBay listing now. By...

    I see you've removed your eBay listing now. By the way, you can buy an entire 760 for under $1500 over here, $2100 (starting) over there (with 74KMI) so I'm not sure how an engine/transmission combo...
  2. [General] Don't do it. I drove my D daily for years,...

    Don't do it. I drove my D daily for years, including winters, while living in upstate New York. The frame and everything bolted to it turned into garbage. The car was great in the snow, but terrible...
  3. Thread: Prv v6

    by dn010
    Replies
    6
    Views
    366

    The transmission would be useless to us and the...

    The transmission would be useless to us and the PRVs in the 760s are not drop in replacements for the DeLorean in that the lower crankcase needs to be changed. So a DeLorean owner buying your engine...
  4. Replies
    11
    Views
    1,392

    Did you try adjusting the pots to see if you can...

    Did you try adjusting the pots to see if you can resolve the loss? (If not, see VR sensor section of your hardware manual for the procedure)
  5. Replies
    11
    Views
    726

    [Heat & A/C] Post #10: ...

    Post #10:

    http://dmctalk.org/showthread.php?18967
  6. Replies
    6
    Views
    261

    [Suspension] Super stuck upper A-arm pivot bolt

    MAPP gas works wonderfully if you use it with a TurboTorch tip.
  7. Replies
    12
    Views
    791

    Poll: [General] ^Agreed^ 80% of the people who see the car...

    ^Agreed^

    80% of the people who see the car remember it "from that movie..." or it's "the Back to the Future car!", 5% know what it is from other experiences in their lives and 15% don't know what...
  8. [Engine] Take it out completely.

    Take it out completely.
  9. [Engine] How bad are the studs? Anything you do is a risk...

    How bad are the studs? Anything you do is a risk - it's really up to you if you want to get involved in replacing them where other things can go terribly wrong, as opposed to cleaning it up and...
  10. [Engine] To comment on your broken engine mount bolt....

    To comment on your broken engine mount bolt. These can seize in the aluminum lower block. Naturally, you'll want to take something and swing at it to get it free but don't or you'll break the ear off...
  11. [Engine] Questions after pulling the motor and transmission

    I want to emphasize that my post said "the clutch kit specifically." Aside from this specific kit being listed as being DeLorean specific, I think it's pretty clear when you find an Amazon Valeo...
  12. Replies
    9
    Views
    542

    [Engine] I've tried one before, wanting to see how it...

    I've tried one before, wanting to see how it would do removing an exhaust manifold. I found the size prevented me from reaching 90% of the areas that I needed to hit with it, engine in car, so it was...
  13. [Engine] I'd replace the clutch/bearing/pressure plate...

    I'd replace the clutch/bearing/pressure plate since you've already got it apart.

    Hint: I know everyone is about "supporting your vendor" but I can't go along with that for the clutch kit...
  14. Replies
    6
    Views
    453

    [Frame & Body] I stopped reading after the tropical storm was...

    I stopped reading after the tropical storm was identified as a hurricane.
  15. Replies
    24
    Views
    1,410

    [Engine] Since you have good numbers on the gauge...

    Since you have good numbers on the gauge connected directly to the engine, I'd say you're doing just fine and wouldn't worry about it. 32 is for 900RPMs and idle is 775 so ~28 would be expected....
  16. Replies
    24
    Views
    1,410

    [Engine] Two marks is correct. See post #57 for...

    Two marks is correct. See post #57 for explaination:

    http://dmctalk.org/showthread.php?13917-Missing-cylinders-during-idle/page6
  17. [Frame & Body] This? https://www.ebay.com/itm/193652921187

    This?

    https://www.ebay.com/itm/193652921187
  18. Replies
    4
    Views
    759

    [For Sale] Sold! Please lock this thread.

    Sold! Please lock this thread.
  19. Replies
    15
    Views
    1,289

    [Engine] When I had no converters, my biggest complaint...

    When I had no converters, my biggest complaint was how much I smelled like exhaust after a drive.
  20. Replies
    4
    Views
    759

    [For Sale] I am sure I can polish this up but here are some...

    I am sure I can polish this up but here are some photos of it's current state.

    66972
    66973
    66974
  21. Replies
    11
    Views
    1,392

    Assuming you're using the stock distributor and...

    Assuming you're using the stock distributor and going by the wiring diagram, you'd use the wire going to the second to last pin of the Ignition ECU. This diagram was taken from the resource section...
  22. Casting is the same as DMCH but the last 3 are...

    Casting is the same as DMCH but the last 3 are 123 and it's apparently for a 240 Turbo after I just looked it up. Not sure how it ended up on a B28 but it did run fine.
  23. [Heat & A/C] :confused0:

    :confused0:
  24. Replies
    2
    Views
    279

    [For Sale] PM Sent.

    PM Sent.
  25. This is what I have. 66790 66791

    This is what I have.

    66790
    66791
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4