FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    7
    Views
    219

    [Engine] Since, as D:01:13 says, they are not used on a...

    Since, as D:01:13 says, they are not used on a DeLorean, why not use epoxy...??
  2. Replies
    49
    Views
    1,461

    [Engine] Uggg...I don't know what I was thinking about,...

    Uggg...I don't know what I was thinking about, with it removed. ...It would obviously read the battery voltage with the meter itself being in series.

    Thanks!
    (It's Ron's fault ;-)
  3. Replies
    49
    Views
    1,461

    [Engine] lol! Try removing all but the white/slate (-...

    lol!

    Try removing all but the white/slate (- side) and a 12V jumper (+ side) on the coil.
    This will eliminate the resistor block, relay, etc.

    It takes some trial and error, but you can usually...
  4. Replies
    49
    Views
    1,461

    [Engine] Hehe.. that wasn't me. Ron versus DMC-Ron. I'm...

    Hehe.. that wasn't me. Ron versus DMC-Ron.

    I'm sure your wires are wrong (because of the capacitor being on the wrong side of the coil and you getting 12V on the white/yellow wire). I can't tell...
  5. Thread: 81 automatic

    by Ron
    Replies
    2
    Views
    2,483

    [For Sale] ...he hasn't logged in since August :-(

    ...he hasn't logged in since August :-(
  6. Replies
    49
    Views
    1,461

    [Engine] ...except you shouldn't be showing 12V on the...

    ...except you shouldn't be showing 12V on the white/yellow wire, ever. You can put 12V on the coil (+) as a test, but don't leave it that way...
  7. Replies
    49
    Views
    1,461

    [Engine] Yes, clearer...I was not getting you had an...

    Yes, clearer...I was not getting you had an o-ring AND and the "extra" copper washer between the pipe and manifold.

    The flag looking thing is the wire harness (each wire is labeled where it goes...
  8. Replies
    49
    Views
    1,461

    [Engine] Maybe I'm not following you... There needs to be...

    Maybe I'm not following you... There needs to be a seal there. (I've seen copper and rubber there.) Its #9 in the link I gave you above.


    In RUN, power (12V) has to go through 2 resistors in the...
  9. Replies
    49
    Views
    1,461

    [Engine] 1. Maybe see if it will stay running with short...

    1. Maybe see if it will stay running with short spurts of staring fluid.
    2. In the vid, the tach appears to show ignition while it is dying (see #1 above ;-).
    3. If you can see the entire opening,...
  10. Thread: Starter shortage?

    by Ron
    Replies
    21
    Views
    1,176

    [Engine] Try this link:...

    Try this link: https://www.oreillyauto.com/search?q=R612473B

    And it does require a simple modification -- You have to add a pigtail as shown HERE.
  11. Thread: Starter shortage?

    by Ron
    Replies
    21
    Views
    1,176

    [Engine] Google it... At O'Reilly, near you :): ...

    Google it...

    At O'Reilly, near you :):

    https://www.oreillyauto.com/search?q=R612473B
  12. Replies
    13
    Views
    831

    [General] It could be the slave, if it isn't new too... ...

    It could be the slave, if it isn't new too... But, I'm with David on starting it in gear while the clutch pedal is down.
  13. Thread: Scammer alert

    by Ron
    Replies
    9
    Views
    878

    Banned.

    Banned.
  14. Replies
    195
    Views
    7,457

    [General] Crows Foot. ...and as you probably guessed, you...

    Crows Foot.
    ...and as you probably guessed, you do not want the Evaporator tube to twist ANY whatsoever!!
  15. Replies
    195
    Views
    7,457

    [General] Wild guessing you put it back together dry??

    Wild guessing you put it back together dry??
  16. Replies
    1,833
    Views
    560,426

    Pantera's had 302s and 351s (Cleveland and...

    Pantera's had 302s and 351s (Cleveland and Windsor).
    Bricklins had a 360 AMC, until they switched to 351 Windsors in 1975.
  17. [General] 8mm = 7.9375" :)

    8mm = 7.9375" :)
  18. [Frame & Body] I sent one (black) to DMCMW to be recovered-...

    I sent one (black) to DMCMW to be recovered- Perfect!
  19. Replies
    8
    Views
    1,055

    [Wanted] +1, Rich That poll is well over two years...

    +1, Rich

    That poll is well over two years old...
  20. Replies
    195
    Views
    7,457

    [General] +1 ..and inspect the slits closely.

    +1

    ..and inspect the slits closely.
  21. Replies
    195
    Views
    7,457

    [General] I wonder if the nozzle tip will stand milling...

    I wonder if the nozzle tip will stand milling...
  22. Replies
    195
    Views
    7,457

    [General] I finally found my reference material. After...

    I finally found my reference material. After viewing THIS VID, I'm with you on the shims (Sorry, played with too many different systems over the years...;-).
    What you are saying makes sense to me,...
  23. Replies
    195
    Views
    7,457

    [General] lol...I can't count the shims/washers in that pic...

    lol...I can't count the shims/washers in that pic much less see them very well...

    I'm with Bitsy, sounds like the nozzles aren't flush with the mating surface.
    If you want, check them with a...
  24. Replies
    195
    Views
    7,457

    [General] I don't see any washers in the pic I pointed to...

    I don't see any washers in the pic I pointed to (only "spring cups")...

    If you're asking about the circle that's off center at ~4 o'clock, that is the end of an adjustment screw found only in the...
  25. Replies
    195
    Views
    7,457

    [General] RE: 2. I don't remember any shims?? (Check out...

    RE:
    2. I don't remember any shims?? (Check out the 2nd pic HERE.)
    (FWIW, the springs should exert .1 bar, assembled, iirc.)
    3. Four slits partially blocked?
    4. Ya distorted the diaphragm...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4