Thanks. I have been looking at the many available printers. I see some have heated plates, heated enclosures, flex plates, and a lot of new stuff I have to read up on.
I was wondering if two...
Type: Posts; User: Bitsyncmaster
Thanks. I have been looking at the many available printers. I see some have heated plates, heated enclosures, flex plates, and a lot of new stuff I have to read up on.
I was wondering if two...
I'm working on printing an HVAC faceplate with improved less light bleeding shields. My Formlabs printer can only print flat to 5.4" and I wanted to print flat so the back side has no supports. I...
The RPM relay turns the lambda system on by powering the "main fuel relay" (lambda relay). First is make sure that lambda relay is the correct type. If you have no FV buzz still then you need to...
I think he was drilling out a stuck bolt and went to deep.
Thanks for the photo. Now it came back to me from 10 or more years ago when I built my first door lock unit. I had the Zilla case which has a circuit breaker mounted inside of it. So I decided to...
Can someone post a photo of the wire end of there harness connector for the door lock unit. Not sure if mine was stock with a large brown wire in the top single pin on the connector. I had the...
There are some engines in other cars where they said to put a sealer on some bolts because they went into the water jacket. I would defiantly try a good sealer on the bolt. Make sure the bolt is...
That looks more like 0.010" or more but as long as both surfaces are parallel it should not be a problem.
Thanks. I contacted them.
You will hear some noise from the primary pressure regulator. Not sure if that noise is always there when engine is running but I hear it if the pump is running without the engine.
Toby has no stock of his fans with connector. He does have them without connector. That is the two pin connector. I have a blue idle ECU connector that came with an idle ECU core I bought. I guess...
I had a customer that wanted to use a remote. So his system seems to use a negative pulse to lock or unlock. So as I was changing the software, I found a bug with the remote operation that I had to...
It's mostly the pins that would require quite an investment to produce. Actually making little changes to pin design would enable the female pins to be removed easily. The AMP connectors are much...
When you go to key position 2 your adding more load so a bad connection could make that feed through go open and kill everything. If it's not the feed though connections then you will need to...
If your battery is good the first thing to check are the two feed through bolts and nuts behind the rear deck board. You have to remove the vertical board by removing the hooks on top which hold the...
I had one side blow fuses and it turned out a screw in the center console shorted a wire on the right side. Try pulling the two screws on the shifter plate and see if your problem goes away.
I was just asking because I had a mug my daughter got me with my grand kids photos on it and a short time later the photos scratched off.
It says hand wash so the Vin print is not done before the mug is glazed? Or is it?
The two inputs are the two empty solder pads labeled W10 and W11. Right now I have software looking for a rising edge to do a lock or unlock. W10 is for lock and W11 is for unlock. Voltage from...
Ive got 8 units (no connector) with 9 inch long wires ready to sell. If you wanted one I will sell for $75 including shipping to US address.
I attached my notes I started for documentation. Also...
Well I've decided the LEDs I got on my last order are the best ones yet. The red color is good and orange are good for the amber lights. I went ahead and ordered circuit boards. The boards ended...
Britishwiring is only showing 16 of the 9 pin pairs in stock. I wonder if they can get more. I do have some 9 pin connectors but I would need a supply of them to sell many units with the connector...
I did some more thought on noise. I could see if the car was moving or on a bad road the ground connections on the door switches could be noisy. So my software remembers what condition the locks...
That was a good test to unplug one door switch and try to screw it up. I was able to very slowly move the switch so the ground lifted and then move it back and it found a bug in my software that...
When both door switches are working, there is no electrical noise since your moving the contacts off one door but the other door keeps the circuit grounded. The only noise you get is when the...