FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: cpistocco

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. [Fuel] Pull the vacuum hose off your vacuum advance on...

    Pull the vacuum hose off your vacuum advance on top of distributor.
    On a cold engine you should NEVER get advance.
    On a warm engine, you should not get advance at idle....only upon acceleration.
  2. [Fuel] timing

    I had a similar problem...
    I was getting vacuum advance when I wasn't supposed to...
    Check microswitch operation and Vacuum solenoid (which is connected to the vacuum line that connects to...
  3. tfc box handle

    Hello
    I have not seen anything on the forum addressing the installation of the "battery cleaner" handle on to the TFC time switch box. To that end, I have a technique that seems to work fairly...
  4. Your relentless pursuit is over! Congrats! I...

    Your relentless pursuit is over!
    Congrats!
    I love the way they look on my car....They make the car pop...
  5. [For Sale] hello I never heard back on the louvers...

    hello
    I never heard back on the louvers...
  6. Thread: Bttf parts

    by cpistocco
    Replies
    7
    Views
    981

    thank you

    thank you
  7. Delorean's Eyebrows- Thumbs up Blonde singers...

    Delorean's Eyebrows- Thumbs up
    Blonde singers fake teardrops- Thumbs down
  8. The Front Bottoms- GINGER

    https://www.youtube.com/watch?v=Imw_l1IA_rc
  9. Poll: But I would be interested in your least expensive...

    But I would be interested in your least expensive displays... :)
    pm sent
  10. Poll: time circuits

    The enclosures are readily available...and reasonable.
  11. Poll: How much?

    What are you asking for time circuit displays?
    ty
  12. Poll: time circuits

    All time circuit enclosures are available (in aluminum or stainless). (3 rectangles plus one large enclosure).
    Gary-ebay
  13. [For Sale] parts?

    Hello
    Would you have a set of louvers? or a grey glove box?
    thanks
    Charlie
  14. You're welcome.... I thought that this would be a...

    You're welcome.... I thought that this would be a nice place for the info.
    And- Yes...for sure... My vacuum solenoid was allowing vacuum to the distributor at idle. Wreaked havoc with my...
  15. How To: Checking timing (timing is everything)

    Credit to David T for this-

    If you need the step-by-step procedure( for checking engine timing) here it is:
    Disconnect and plug the vacuum line to the distributor vacuum advance capsule.
    Clean...
  16. Thread: Bttf parts

    by cpistocco
    Replies
    7
    Views
    981

    Yes- What do you have? :)

    Yes- What do you have? :)
  17. Replies
    3
    Views
    704

    [Wanted] Thank you.... :)

    Thank you.... :)
  18. Replies
    10
    Views
    554

    Crazy question....If you remove electrical...

    Crazy question....If you remove electrical connector from Vacuum advance solenoid, do your rpms go down...and does that close off vacuum to the advance on distributor? (I am far from a Delorean Guru)
  19. Replies
    3
    Views
    704

    [Wanted] glove box lid

    Looking for a glove box lid. Grey. Seems like the only thing available now are reproductions.
    Has anyone tried the repros yet?
  20. Replies
    10
    Views
    554

    vaccum advance at idle

    I had a problem where my car would stumble/ detonate/ knock from a dead stop. Happened only when warm. After fiddling around, (and with some help from Dave and DMC Humble) I found that my micro...
  21. Replies
    7
    Views
    370

    fun filled fact

    Here is a Fun-filled-fact concerning rpm Relay (and any other relay, for that matter).- Relay should ALWAYS be in the upright position (wires down) to work properly.
  22. Replies
    56
    Views
    9,231

    [General] Thanks again, everyone, for all of the help. :)

    Thanks again, everyone, for all of the help. :)
  23. Replies
    56
    Views
    9,231

    [General] Cleaned it, sprayed it with degreaser, cleaned it...

    Cleaned it, sprayed it with degreaser, cleaned it again, and epoxied it...and prayed.
    I will let everyone know when it fails... :)
  24. Replies
    56
    Views
    9,231

    [General] column bushing / grommit

    Thanks Guys...
    I think that maybe the hole in the firewall got sloppy from not having a bushing....and now the new bushing isn't seating tightly. To make matters worse, I had greased everything...
  25. Replies
    56
    Views
    9,231

    [General] When you turn the steering wheel, the bushing...

    When you turn the steering wheel, the bushing should not turn, right?
    Has anyone ever tried to hold the bushing with a sheet metal screw on either side, 180 Degrees apart?
Results 1 to 25 of 362
Page 1 of 15 1 2 3 4