FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: cis6409

Page 1 of 4 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    7
    Views
    4,485

    [General] Just read your thread post #27 there Dana,...

    Just read your thread post #27 there Dana, fantastic write up , that is a huge help.
    Have a good idea where the molex side of the connector is located now and how to feed it through.

    Virtually...
  2. Replies
    7
    Views
    4,485

    [General] Thanks guys for the replies. excellent stuff...

    Thanks guys for the replies.
    excellent stuff will check out that thread and have a closer look at the plastic connector.

    Thanks a mill,
    Shane
  3. Replies
    7
    Views
    4,485

    [General] Air con dryer wiring looms

    Hi guys
    Just wondering is it a big job to replace these 2 looms for the air con dryer.
    I have a broken wire on one of the Connectors and I can't see a way of getting into the terminals without...
  4. Replies
    15
    Views
    1,710

    [General] I didn't know you were delorean less either! (not...

    I didn't know you were delorean less either! (not on Facebook myself to)

    It's a huge decision to move like that but congrats and best of luck with it, hopefully you ll be an owner again soon....
  5. Replies
    3
    Views
    316

    [General] Thanks for that guys I didn't know some come...

    Thanks for that guys
    I didn't know some come with the grommet pre-installed. I'll check it out.

    You learn something new every day with these cars!

    Thanks
  6. Replies
    3
    Views
    316

    [General] Lower speedo cable grommet

    Does anyone have any tips for installing the rubber grommet over the lower speedo cable. I have bought a new lower cable and grommet.
    With some heat I can get the grommet to slip over the end part, ...
  7. Replies
    6
    Views
    371

    [General] O I see now, excellent thanks! Shane

    O I see now, excellent thanks!


    Shane
  8. Replies
    6
    Views
    371

    [General] I've got the plate refitted Great to finally...

    I've got the plate refitted
    Great to finally have it in the correct place and not hanging down..
    One other question the flasher relay is supposed to be attached to that aswell but instead of the...
  9. Replies
    6
    Views
    371

    [General] Thanks guys that's great! Cheers Shane

    Thanks guys that's great!

    Cheers
    Shane
  10. Replies
    6
    Views
    371

    [General] Wiper control module

    Hi guys
    Just trying to tidy up my wiring routing for under the steering column and inertia switch etc.

    At the moment it's just cable tied to the lambda counter loom and it's all just hanging.
    ...
  11. Replies
    5
    Views
    395

    [General] Thanks guys for the tips and info, that answers...

    Thanks guys for the tips and info, that answers my question. Cool.


    Cheers
    Shane
  12. Replies
    5
    Views
    395

    [General] Suspension bolts tensile ratings

    Hi guys
    I'm doing a front and rear suspension rebuild as part of my frame restoration.

    I'm Replacing the pivot and lower link bolts and wanna make sure I get the correct ones. What tensile or...
  13. Replies
    24
    Views
    1,905

    [Fuel] Glad to see your getting the issue sorted. ...

    Glad to see your getting the issue sorted.

    What fixed the frequency valve? It would help other owners when similar issues come up.. Was it a wiring issue or was the valve itself bad?

    Shane
  14. Replies
    24
    Views
    1,905

    [Fuel] Get the frequency valve working first , car will...

    Get the frequency valve working first , car will never run right with it not functioning.
    As Michael says, a little backstory info would help..
  15. Replies
    8,839
    Views
    1,956,867

    [General] Great job tidyed up very nice..:) What...

    Great job tidyed up very nice..:) What color/shade of grey did you use?
  16. Replies
    8,839
    Views
    1,956,867

    [General] I try and edit these photos and save the sideways...

    I try and edit these photos and save the sideways even to try and get the to go straight when i post but they just won't. Can anyone tell me how to get this right?[/QUOTE]


    I've had this problem...
  17. Replies
    8,839
    Views
    1,956,867

    [General] Lovely stuff, always nice to get to that point...

    Lovely stuff, always nice to get to that point where the shiny stuff can go back on!
  18. Replies
    31
    Views
    6,080

    [Engine] Great to hear!

    Great to hear!
  19. [Electrical] I do not know for sure what the 58 ohms is....

    I do not know for sure what the 58 ohms is.
    Hopefully you can get to the bottom of it
    Good luck with it.

    Shane
  20. [Electrical] Hi lars I'm not 100% sure on this but I think...

    Hi lars
    I'm not 100% sure on this but I think this is how it's routed/wired up..


    The first blue/yellow wire from the engine harness blue plug is the signal feed from the starter solenoid...
  21. [Electrical] Peel off the old one and clean off any residue...

    Peel off the old one and clean off any residue glue left behind. Then re stick the new one on.
  22. [Electrical] I had the same issue. The reproduction a/c panel...

    I had the same issue. The reproduction a/c panel decal I bought was to blame.
    They are not opaque enough. Changed to the oem decal from Houston and it was sorted.

    Check the connection for the...
  23. Replies
    28
    Views
    9,138

    [Engine] No, no issues of peeling or adhesion - Once the...

    No, no issues of peeling or adhesion - Once the prep is done correctly it should be good.
    I don't know if anyone else has ever done this on other prv blocks, I know no one else in Ireland has done...
  24. Replies
    28
    Views
    9,138

    [Engine] Hi Yes it was holding fine no issues at all it...

    Hi
    Yes it was holding fine no issues at all it held up well. however the car is off the road for last while as Im doing a full engine rebuild. Nothing to do with the block rot, thankfully.

    40...
  25. Replies
    8,839
    Views
    1,956,867

    [General] Got a chance to finish off the starter motors....

    Got a chance to finish off the starter motors. Never got round to sorting my Paris rhone starter when it eventually gave up - Just needed a new solenoid. So redone both.
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4