FRAMING JOHN DELOREAN - AT THEATERS THIS WEEKEND & ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: FABombjoy

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    581

    [Engine] Unfortunately the available engine literature is...

    Unfortunately the available engine literature is ambiguous on the subject.

    Volvo TP30430-1 specifies the three thermostats as "Type 1" "Type 2" and "Type 3", with low opening temps at 178, 187,...
  2. Replies
    22
    Views
    893

    [General] Isn't the stock bleed screw BSP? The OD of 1/16...

    Isn't the stock bleed screw BSP? The OD of 1/16 BSP is less than 5/16. I've not seen that referenced as metric before.

    I with with "hack" based on the visible 2lbs of goo squished out from the...
  3. Replies
    22
    Views
    893

    [General] Definitely a PO hack! It'll probably never be...

    Definitely a PO hack!

    It'll probably never be a bleeder again as the tapered seat is likely drilled away. Might best be replaced with a barb using the next size up NPT or something similar, and a...
  4. [General] Just spoke with TCFF staff - Patrick and I will...

    Just spoke with TCFF staff - Patrick and I will have our cars at the FJD showing on the 1st

    ...and for some reason I volunteered to be part of a photo booth type experience during the open space...
  5. [General] I think both Patrick & I can attend if TCFF would...

    I think both Patrick & I can attend if TCFF would like a few cars on display.
  6. Replies
    150
    Views
    41,024

    That's a perfect spot! Unless you have some T-rex...

    That's a perfect spot! Unless you have some T-rex in your family tree :D
    https://i.imgur.com/NJkKM6Q.jpg
  7. Replies
    22
    Views
    818

    [Engine] I would take all that money you're going to spend...

    I would take all that money you're going to spend on AN fittings, hoses, electric pump, wiring, etc., and put it toward EFI instead:



    #1: VOD access in 10 minutes on a well set up EFI system,...
  8. Replies
    12
    Views
    483

    [Engine] Imagine the radiator on the other side and the...

    Imagine the radiator on the other side and the expansion tank on the return hose.

    https://i.imgur.com/9ioIzHU.jpg
  9. Replies
    211
    Views
    40,599

    [Engine] "Twice" is probably not accurate, but I had one...

    "Twice" is probably not accurate, but I had one offered to me when I was looking to build a crank position setup, and it was very noticeably heavier. As soon as I picked it up I knew it wasn't going...
  10. Replies
    211
    Views
    40,599

    [Engine] The early Volvo PRVs have a different main...

    The early Volvo PRVs have a different main pulley, featuring the double AC belt setup. Also weighs about twice as much as a DMC pulley! I wouldn't be surprised if there were a small variety of...
  11. Replies
    211
    Views
    40,599

    [Engine] A larger pulley would underdrive the water pump,...

    A larger pulley would underdrive the water pump, though. I've read a few 3.0 builds but I don't recall seeing pulley size addressed. Is there a build thread or resource where this is discussed?
  12. Replies
    26
    Views
    1,077

    [Frame & Body] The hardware store stuff should work fine. I use...

    The hardware store stuff should work fine. I use it with those cheap acid brushes.
    Apply it per the directions and you should be set: Light coat on both surfaces, wait until tacky, then slowly and...
  13. Replies
    26
    Views
    1,077

    [Frame & Body] Use contact cement, not RTV. -Easier to...

    Use contact cement, not RTV.

    -Easier to position as you install it - no taping or drying period
    -Removable with adhesive remover
    -Doesn't squish out and seep from around the seal
  14. [General] D:02:01 in the service manual has the...

    D:02:01 in the service manual has the specifications.
    Checking value: 4.9-5.5 bar
    Setting value: 5.1-5.3 bar

    4.5 bar (450kPa) would be a bit low.
  15. Replies
    11
    Views
    805

    Prefect Percy strikes again

    Prefect Percy strikes again
  16. Replies
    11
    Views
    805

    Friend, ship to yyz. Iz long drive but cheap

    Friend, ship to yyz. Iz long drive but cheap
  17. Replies
    1
    Views
    293

    [For Sale] Sold!

    Sold!
  18. Replies
    1
    Views
    293

    [For Sale] K-Jetronic Pressure Tester TU-14

    Hoffman TU-14 fuel pressure tester. Only used a few times.

    https://imgur.com/a/5GVBfRK

    $65 delivered to US, or $55 + actual international.
  19. Replies
    7,906
    Views
    1,226,808

    [General] Sure beats buying a refurbished WUR :) Don't...

    Sure beats buying a refurbished WUR :) Don't forget to plug the hole or you'll go lean on throttle during warmup.
  20. Replies
    23
    Views
    1,889

    [General] Let me see how far I can get with it. It'll...

    Let me see how far I can get with it. It'll probably be some time though.

    In my car I'll be installing an EFI-specific gauge and controls for heated/cooled seats, so I can't be of much help.
  21. Replies
    18
    Views
    2,130

    Other than you, two sentences previously :D ...

    Other than you, two sentences previously :D

    It's not really an Apple thing as EXIF is a standard. It's the ancient software here that doesn't understand the orientation metadata or prematurely...
  22. Replies
    18
    Views
    2,130

    Like everyone on the internet I'm just full of...

    Like everyone on the internet I'm just full of opinions. But I'm glad someone is interested ;)


    That would apply to the published image. I agree that EXIF should be stripped from the final...
  23. Replies
    18
    Views
    2,130

    They are size reduced to the point of becoming...

    They are size reduced to the point of becoming illegible.

    Or people post images and the orientation is wrong. The standard response is to make fun of their device rather than fix a software...
  24. Replies
    18
    Views
    2,130

    Could also use an update the ancient server...

    Could also use an update the ancient server versions of gd or imagemagick that can't handle EXIF data and totally ruins PNG files
  25. Replies
    23
    Views
    1,889

    [General] If you're taller than a toddler, it won't block...

    If you're taller than a toddler, it won't block your view :) I have dual gauge pods on the console that are just about the same height. No issues.

    I'm (slowly) building a 3D printed mounting...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4