FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    116
    Views
    18,160

    [General] You've already spelled it out, twice now....

    You've already spelled it out, twice now. However, I'm confused:
  2. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    785

    [Engine] Oil Pump Spring?

    Like Ron stated, the valve does not regulate pressure. It only opens at a certain PSI to bleed high pressure. This argument doesnít really matter since regardless, there are no springs available for...
  3. Replies
    40
    Views
    6,759

    My reman starter would also clank repeatedly,...

    My reman starter would also clank repeatedly, started with once in a while to about 5-10 times turning the key until it would actually engage. Turned out to be a loose ground for me, maybe this is...
  4. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    785

    [Engine] I should specify that I'm talking about the Volvo...

    I should specify that I'm talking about the Volvo B280F pump springs that were broken.

    Unfortunately I have not found anywhere to get replacements so I have a few pumps laying around. These pumps...
  5. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    785

    [Engine] The Volvo springs are shit. Two of the three...

    The Volvo springs are shit. Two of the three pumps I took apart had broken springs. The spring in the D seems to be better made than those.
  6. Replacing bunch of Alternator Wires for larger 4 gauge Single wire cable?

    Yes, I removed the brown wires and ran a battery cable from the alternator to the bulkhead. The brown wires were very corroded and this was my best option. I ran the wire down the pontoon instead of...
  7. Replies
    13
    Views
    699

    [Transmission 5-Speed] Your guess is inaccurate. It's really not that...

    Your guess is inaccurate. It's really not that hard to remove a fitting, put your finger over the drain hole and then quickly swap your finger for the drain plug. You will lose some fluid but you...
  8. Replies
    13
    Views
    699

    [Transmission 5-Speed] Or... you can just use a barb fitting in the...

    Or... you can just use a barb fitting in the drain opening along with a hand pump & hose on your gear oil bottle to get the measured amount of oil back in.
  9. Replies
    7
    Views
    247

    I too am curious about this comment.

    I too am curious about this comment.
  10. Replies
    4
    Views
    403

    [Wanted] I am not sure if any of these are early or not,...

    I am not sure if any of these are early or not, but Whiteout is selling a pair of front wheels:

    https://www.ebay.com/itm/Delorean-Front-Wheel-Genuine-DMC-12-No-Core-PAIR-of-Wheels/223601689943
    ...
  11. [General] Was going to edit this into my post but others...

    Was going to edit this into my post but others posted as well. There may be a how-to guide here but this is the one I used, back in the day.

    https://www.dmcnews.com/Techsection/lightrelays.html
  12. [General] Really all you need to do is go get a relay and a...

    Really all you need to do is go get a relay and a socket and wire it in. There are mods you can do as well like turn the lights off when you turn the key off without pressing the headlight switch...
  13. Replies
    14
    Views
    959

    [General] You may want to consider doing both it you do one...

    You may want to consider doing both it you do one so theyíre not mismatched after itís all done.
  14. Replies
    14
    Views
    959

    [General] Tough decision you'll have to make. We can't see...

    Tough decision you'll have to make. We can't see what you're working with nor are we getting the bill for the work. I will say that if you don't like it, change it.
  15. Replies
    19
    Views
    1,587

    [Suspension] When I had noise issues over any little bump in...

    When I had noise issues over any little bump in the road, my lower control arm bushing was shot - the rubber was pretty much all pressed out of the bushing and this allowed everything to move around....
  16. Replies
    14
    Views
    959

    [General] I have gotten away with polishing up the black...

    I have gotten away with polishing up the black portions since I've had my car but it is time for me to refresh them completely. Here is the thread I started with info on what black to use:
    ...
  17. Replies
    19
    Views
    1,587

    [Suspension] Here is my guess - what is the condition of your...

    Here is my guess - what is the condition of your lower control arm bushings?
  18. [General] Find out whose stainless arms you have and...

    Find out whose stainless arms you have and contact them for input on changing the bushings (I'm not aware of anyone other than DPI selling stainless ones so you might start there). From what I...
  19. Replies
    15
    Views
    1,010

    [Frame & Body] It might be better to use a block of wood so that...

    It might be better to use a block of wood so that it can absorb some of the strike should the bar/bracket release on you while you're adjusting it.
  20. [General] You donít need to worry about the spring, the...

    You donít need to worry about the spring, the shock is there holding everything together.
  21. [General] I can't remember if I've replaced the upper...

    I can't remember if I've replaced the upper bushings or not on mine, instead it is always the lower ones that have gone bad. You could take it apart an try it with a bushing tool but personally I'd...
  22. [General] The UPPER control arms don't need the springs to...

    The UPPER control arms don't need the springs to be removed in order to remove the arm.

    You can A- lift the car up and remove the upper arm or B- rest the weight of the car on a jack or block etc....
  23. Replies
    18
    Views
    1,049

    [Engine] If all else fails, you can try soaking the 2.8L...

    If all else fails, you can try soaking the 2.8L cap in gas or solvent to try to clean up the internals and see if it works any better than it did. Unfortunately I only have the B280F 'separator'...
  24. Replies
    62
    Views
    3,874

    [Suspension] The difference I could tell between early/late...

    The difference I could tell between early/late frames was that they riveted the plate on the underside of the engine cradle on early frames where the lower links are located (I can try to take a...
  25. Replies
    170
    Views
    46,330

    The cups would make shifting difficult on the...

    The cups would make shifting difficult on the 5-speed.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4