FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Delorean Industries

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    34
    Views
    4,629

    [Electrical] yes!!!!!!

    yes!!!!!!
  2. Replies
    2
    Views
    301

    [Wanted] https://deloreanindustries.com/lower-door-strut-re...

    https://deloreanindustries.com/lower-door-strut-reinforcement-bracket-kit-stainless/
  3. Replies
    32
    Views
    1,261

    [General] However much you actually paid for the car on the...

    However much you actually paid for the car on the bill of sale/title is what you will be paying sales tax on.
  4. Replies
    5
    Views
    337

    [Frame & Body] We extrude high tolerance profiles of this gasket...

    We extrude high tolerance profiles of this gasket in small batches. Instead of making 2500 feet at a time with the material on the shelf aging you are always getting a seal six months or less in age...
  5. [For Sale] We will supply new flange gasket free of charge...

    We will supply new flange gasket free of charge to buyer in United States.
  6. [Brakes] Body tub needs to be lifted to properly install...

    Body tub needs to be lifted to properly install our line section with all of the required mount locations. It is impossible to achieve perfect orientation without doing so.
  7. Replies
    8,456
    Views
    1,572,367

    [General] Our advice as to reduce the risk of damaging if...

    Our advice as to reduce the risk of damaging if you can't remove the entire crate from the truck is this procedure.

    Condensed instructions:

    ___ Min 4 people to assist
    ___ Center crate in the...
  8. Replies
    13
    Views
    1,132

    [General] We are trying to get caught up and are assembly...

    We are trying to get caught up and are assembly as fast as we use on builds. Should be available again later this month. No fitment disclaimer for us though. :)
  9. You actually ordered billet front lower arms with...

    You actually ordered billet front lower arms with the Coilover system. No need to box the factory front lower arms. The only things you will need to refurbish are the rear upper and lower links,...
  10. Replies
    18
    Views
    1,231

    [Brakes] Not with a factory brake configuration. You...

    Not with a factory brake configuration. You should maintain the proper bias for how the system is designed. We change the bias along with other components for our specific requirements.
  11. Replies
    18
    Views
    1,231

    [Brakes] Our cast units are stock bias and billet units...

    Our cast units are stock bias and billet units are 50/50 for our brake system upgrade.
  12. Replies
    18
    Views
    1,231

    [Brakes] Blanket statements are never a good thing. ...

    Blanket statements are never a good thing.

    ___Our brake master cylinder bodies are cast in Southern Ohio. Engineered off an original Girling unit.

    ___ Our main body machine work is performed...
  13. [For Sale] Sold.

    Sold.
  14. [For Sale] Delorean Industries spec twin turbo gen 1

    For sale Delorean Industries spec twin turbo gen 1 crate engine. Dyno rated at 398 ft lbs. includes fully blueprinted forged internal engine, turbo system complete with intercoolers. Will require a...
  15. [Suspension] We offer the top stud bushings in both poly and...

    We offer the top stud bushings in both poly and rubber. We can send you out a set today of the rubber version if you would like. Just let us know!
  16. [Engine] Kinda like going to a house of worship. You are...

    Kinda like going to a house of worship. You are expected to tithe as a franchise will only deal with you while one hand is in your pocket. On the other hand, we are always more than happy to tell you...
  17. [Electrical] Yeah, I wouldn't discount the hardship the...

    Yeah, I wouldn't discount the hardship the electronics went through during that period. Like most things in life, only so much abuse can be taken before a hard failure.
  18. [Electrical] Remember that time you stopped by and your...

    Remember that time you stopped by and your starter was held in by 1 7mm bolt when it is normally held in by 3 8mm ones? The amount of stress on the electrical system had long term side effects.
  19. [Engine] Kris, from the above measuring pictures and...

    Kris, from the above measuring pictures and dimensions you have given once the block deck surface has a high micron finish applied for true up and gasket sealing you will be within spec. I would...
  20. [Engine] This is terrible.

    This is terrible.
  21. [Electrical] Definitely not one of ours. All of our units have...

    Definitely not one of ours. All of our units have black powder-coated finished fans, billet bracket, billet pulley, and 5/16 bolt instead of the 10mm. This is Hervey's unit for sure.
  22. Replies
    86
    Views
    12,381

    We offer just about everything separate from our...

    We offer just about everything separate from our full system for owners looking to do a DIY build.

    www.deloreanindustries.com
  23. [Suspension] We built a factory configuration spring...

    We built a factory configuration spring compressor. This mounts to the two lowest exposed coils and has a hat feature that goes over the shock tower. When used it pulls the spring up to the frame and...
  24. We also save all good mild steel chassis removed...

    We also save all good mild steel chassis removed for frame updates. If your current frame is beyond repair, we have a massive stockpile of good mild steel chassis available.
  25. Yes, that is the all-out version with all of the...

    Yes, that is the all-out version with all of the add ons and EFI provisions. Significantly cheaper without all of that bare-bones.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4