FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DMC-81

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 32 minute(s) ago.

  1. DCF Event: Celebration Exotic Car Festival April 10th, 2021

    Greetings DCF members and DeLorean enthusiasts!

    Join us in Central Florida on April 9th-13th as we participate in the 18th annual Celebration Exotic Car Festival children’s charity event! This...
  2. Replies
    31
    Views
    1,062

    I don't see the typical eyebrow problem. The...

    I don't see the typical eyebrow problem. The fascia is sagging in the middle. Because this is the parts car, most likely the Front Facia Reinforcement panel (Part # 105678 ) was scavenged off the...
  3. Replies
    3
    Views
    398

    [Transmission 5-Speed] Aside from trying the bench bleeding mentioned...

    Aside from trying the bench bleeding mentioned above, I have two other tips:

    1) If you still have the original plastic washer at the slave, replace it with a soft metal one ( copper / aluminum )....
  4. Replies
    29
    Views
    2,034

    [Transmission 5-Speed] Oh man, that's unfortunate. I wonder if the block...

    Oh man, that's unfortunate. I wonder if the block can be repaired by filling in the boss with aluminum (i.e. welded) and then tapped for a new bolt? I had a larger that a quarter sized hole filled in...
  5. Replies
    29
    Views
    2,034

    [Transmission 5-Speed] The pilot bearing is not tight in the crankshaft...

    The pilot bearing is not tight in the crankshaft holder, but if you are concerned about it slipping, you can use a bearing retainer ( Loctite 648 or similar).
  6. Replies
    29
    Views
    2,034

    [Transmission 5-Speed] Thanks, and good luck with the task.

    Thanks, and good luck with the task.
  7. Replies
    29
    Views
    2,034

    [Transmission 5-Speed] Without knowing the history, maintenance, or...

    Without knowing the history, maintenance, or miles on the gearbox, I would say that it is unlikely the nose bearing that's worn. There is a relatively soft input shaft coupler on the other end of...
  8. Replies
    18
    Views
    1,490

    In 2016, I installed a DMCH aluminum radiator and...

    In 2016, I installed a DMCH aluminum radiator and with refreshed OEM cooling fans, they keep my car consistently cool even in the hot Florida summers. It was plug and play with no fitment issues.
    ...
  9. Replies
    27
    Views
    11,147

    I hooked my AUX following Todd's directions and...

    I hooked my AUX following Todd's directions and they worked fine for me as well.

    Also, if the tone controls are upstream of the volume controls, doesn't that mean that you can adjust them before...
  10. [General] Pm'ed. I'll take a black one! I missed the...

    Pm'ed. I'll take a black one!

    I missed the first round and was wondering if these would be made again.
  11. Replies
    21
    Views
    2,347

    James and team: These are excellent enhancements...

    James and team: These are excellent enhancements to the parts store website!! I like the improved parts diagram with functionality. Very nice work! :hihi:

    As a project manager, I know scope creep...
  12. Yes. That is the kit I used, and was happy with...

    Yes. That is the kit I used, and was happy with it.
  13. Replies
    32
    Views
    6,284

    [Frame & Body] My understanding from talking to James Espey when...

    My understanding from talking to James Espey when I needed the correct early paint code is that the first page is a water based formula (i.e. EHP - Envirobase High Performance), and the second page...
  14. [Engine] My experience

    Hi Jonathan,

    In addition to what was posted above I would suggest that you do not need to remove the rear facia depending on the tools that you have available. You do need to remove the exhaust...
  15. Replies
    8,558
    Views
    1,714,086

    [General] Congrats Korey! It's a nice looking car. :thumbup:

    Congrats Korey! It's a nice looking car. :thumbup:
  16. [General] Thanks for putting that together, nice job. I...

    Thanks for putting that together, nice job. I hadn't seen most of the footage before.
  17. Replies
    8,558
    Views
    1,714,086

    [General] Lol! If your DeLorean's horn sounds like any...

    Lol! If your DeLorean's horn sounds like any dying animal, it's time to replace both and check the wiring and ground. I replaced both mine with the original Mixo units from DMC when I restored the...
  18. Replies
    54
    Views
    13,901

    Wow, you're right....great video. Thanks for...

    Wow, you're right....great video. Thanks for sharing.
  19. Replies
    45
    Views
    5,943

    Great progress so far! :thumbup:

    Great progress so far! :thumbup:
  20. Replies
    6
    Views
    474

    [Engine] Yes, I would find a slightly larger o-ring. It...

    Yes, I would find a slightly larger o-ring. It should fit snug.
  21. [General] I found that I needed 28 ft/lbs to properly crush...

    I found that I needed 28 ft/lbs to properly crush the washer and provide a leak free installation.

    More information here:...
  22. Replies
    15
    Views
    2,337

    [General] Very cool product. :thumbup:

    Very cool product. :thumbup:
  23. Replies
    1
    Views
    776

    No tips. I would contact the vendor.

    No tips. I would contact the vendor.
  24. I think the Renault Alpine is okay, but it...

    I think the Renault Alpine is okay, but it reminds me of the Fuego. I can think of other 1985 cars that I would rather have.

    Otherwise, I agree with what has been said so far. In addition the car...
  25. Replies
    12
    Views
    936

    [General] One thing to be aware when putting this list...

    One thing to be aware when putting this list together is the strength of a given bolt. It is marked on the head. While stainless steel looks great, it is not a high strength material. I would take...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4