FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    6
    Views
    2,513

    I just thought of a way to test the tank and the...

    I just thought of a way to test the tank and the check valve. After shutting the engine off, see how many times you can switch from one mode to another and stop hearing the actuators and flaps work....
  2. Replies
    12
    Views
    264

    [Electrical] By the way, it takes a long drive to charge a...

    By the way, it takes a long drive to charge a battery that is quite low on charge. If your car sits 3 months and still has the door lock ECU and clock connected it will be about half charged.
  3. Replies
    10
    Views
    243

    [Heat & A/C] You should see close to battery voltage. If your...

    You should see close to battery voltage. If your only seeing 5 volts than your circuit breaker of a bad connection is probably dropping the voltage. What does your dash voltage gauge read with the...
  4. Replies
    10
    Views
    243

    [Heat & A/C] Speeds 3 and 4 run though two relays used to...

    Speeds 3 and 4 run though two relays used to reduce current through the fan switch. Speed 4 runs power directly to the blower (no resistor).
  5. Replies
    25
    Views
    781

    [Frame & Body] What I did was put the 14 gauge fence wire at the...

    What I did was put the 14 gauge fence wire at the sew seam and fold the cover over on that seam. Then I start pulling the ty-wraps tight, turn the seat over and work the cover to the back, tighten...
  6. Replies
    25
    Views
    781

    [Frame & Body] Well here is the bottom of the passenger seat. ...

    Well here is the bottom of the passenger seat. This one seems looser than the drivers seat. I even used ty-wraps so it pulled tighter than hog rings. I still have to attach the sides but as you...
  7. Replies
    0
    Views
    148

    DMCH was shown on Texas Metal show

    Last night I was watching Texas Metal which is one of the many car build shows on my favorite TV channel. They modified a classic El Camino with what the customer asked for (A 2075 year interior). ...
  8. Replies
    25
    Views
    781

    [Frame & Body] I attached the plastic parts with hog rings like...

    I attached the plastic parts with hog rings like the original covers were attached. That will keep the seat back tight in the middle.
  9. Replies
    25
    Views
    781

    [Frame & Body] The plastic is made with the cloth so it will not...

    The plastic is made with the cloth so it will not pull off the cloth. You can buy that material for people that are sewing there own seat covers. The L-seat covers have that only on the back where...
  10. Replies
    42
    Views
    1,567

    [General] I measured it after the seat cover was installed...

    I measured it after the seat cover was installed and the bottom (side to seat) is 2 3/4" and the top edge of the steel latch is a little more at 2 7/8". The OEM cover the cut bottom screw hole is...
  11. Replies
    42
    Views
    1,567

    [General] Well I forgot to take into account for the foam...

    Well I forgot to take into account for the foam getting compressed a little. So my cut at 3" from the edge should have been about 2.75". So remember that when your ready to make your cut.

    Well...
  12. Replies
    42
    Views
    1,567

    [General] Measuring the cut location

    This is how you measure where to make you cut. After finishing the other side so you know where the edge of the skin should sit, you use a tape measure to locate your cut location. Remember the...
  13. Replies
    42
    Views
    1,567

    [General] This is how much foam you need to cut off. Not...

    This is how much foam you need to cut off. Not that it matters because you don't see the shorter sides but I wonder if this is only a problem with the L-seat covers. You can't pull that edge down...
  14. Replies
    42
    Views
    1,567

    [General] Agreed. Doing the covers is like doing isometric...

    Agreed. Doing the covers is like doing isometric exercise do to the constant pulling and maneuvering to do the hog rings.

    I did buy an air powered stapler and 3/16" staples and will see how that...
  15. Replies
    42
    Views
    1,567

    [General] This second seat cover the ribs in the back...

    This second seat cover the ribs in the back section were to long. I guess someone messed up when they made the cover. The other set was fine. That is the sewn fabric with the plastic rib you hog...
  16. Replies
    17
    Views
    531

    You know you can run wire from the front side...

    You know you can run wire from the front side marker to the back side marker and have it work both. I had one customer do that but most people don't want to run those wires and buy two units.
  17. Replies
    42
    Views
    1,567

    [General] I started recovering the passenger seat. This...

    I started recovering the passenger seat. This one seems to be more of a problem in that It takes much more work to stretch it. I had done the first one outside and temps were higher so that may be...
  18. Replies
    42
    Views
    1,567

    [General] My seat release back levers are pointed to the...

    My seat release back levers are pointed to the back. I thought that was stock but maybe not.
  19. Replies
    9
    Views
    312

    [Electrical] I think if the tach moves when cranking, the coil...

    I think if the tach moves when cranking, the coil has to be getting fired so resistors feeding the primary must be connected. I know the RPM relay and idle ECU use the inductive spikes from the...
  20. Replies
    9
    Views
    312

    [Electrical] Make sure your white bulkhead connectors are not...

    Make sure your white bulkhead connectors are not swapped. If your tach moves when cranking the ignition ECU is probably good.
  21. Replies
    4
    Views
    204

    [Fuel] I agree because going down hill your not using...

    I agree because going down hill your not using much gas.
  22. Replies
    4
    Views
    204

    [Fuel] I've always wondered the same. I not sure if...

    I've always wondered the same. I not sure if tanks in new cars have a sump where the pump sits. I don't see any sump looking at the bottom of new cars.
  23. Replies
    101
    Views
    14,066

    It looks like that will only blink the side...

    It looks like that will only blink the side lights if the "running lights" are on.
  24. Replies
    8,454
    Views
    1,570,792

    [General] I take the D when I'm just driving to the post...

    I take the D when I'm just driving to the post office to mail some packages. This morning my driver door would not release the front latch when I went to get back in the car. I don't lock the doors...
  25. Replies
    25
    Views
    781

    [Frame & Body] The lever just pulls off. It sits on some flat...

    The lever just pulls off. It sits on some flat metal with teeth shaped on the metal edges.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4