FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. [General] When I put my stainless letters on my bumper I...

    When I put my stainless letters on my bumper I cleaned that area with MEK which is the strongest solvent I know. I just used it on Q-tips and it did no damage so I would expect if you wipe down the...
  2. Replies
    7
    Views
    225

    [Electrical] I assume that diode was done for a car that did...

    I assume that diode was done for a car that did not have diodes to make each door work like ours. It is best to short the diode so you don't drop another 0.7 volts going to your light. Some LEDs...
  3. Replies
    12
    Views
    248

    How does it tell you "if the system is...

    How does it tell you "if the system is contaminated or you only need to add a small amount".

    Just one ounce of liquid refrigerant will give you the same static pressure as a full two pounds.
  4. [Fuel] The float would have to stay floating on the...

    The float would have to stay floating on the surface of the gas in the tank. What your photos show does not look correct since the float would tilt at an angle in the gas. The arm on the resistor...
  5. Replies
    8
    Views
    241

    [Electrical] The RPM relay is looking for an ignition pulse to...

    The RPM relay is looking for an ignition pulse to run the fuel pump. Switching electrical loads can cause the ignition ECU to fire a pulse. I have seen it happen on my car which did not have the...
  6. Replies
    7,992
    Views
    1,262,649

    [General] If you don't cut the ground wire from the inertia...

    If you don't cut the ground wire from the inertia switch you will still be conducting some current through the dash gauge ground wire. I guess if you use a very heavy gauge new wire and get a good...
  7. Replies
    31
    Views
    1,244

    I've got to many products now. I will have more...

    I've got to many products now. I will have more time when my grand kids get older.
  8. Replies
    31
    Views
    1,244

    When I first saw your photos of your unit I...

    When I first saw your photos of your unit I guessed you would need to charge a lot for the units. I think you could produce new circuit boards with electronics on them for a price that should sell...
  9. [Electrical] Yes it sounds like your CSV is not working but it...

    Yes it sounds like your CSV is not working but it could be something else is temperature sensitive. The CSV seems to have low failure rates unless it sits a long time without use. The most common...
  10. Replies
    7,992
    Views
    1,262,649

    [General] I dumped a bottle of fuel injector cleaner into...

    I dumped a bottle of fuel injector cleaner into my tank and drove about 10 miles. It may be my imagination but it seems to be running very smooth now. With a standard transmission you tend to feel...
  11. Replies
    3
    Views
    190

    Pretty sure that connects to a mating connector...

    Pretty sure that connects to a mating connector that goes to a ring terminal to be grounded to the engine block. With that ground missing your lambda system won't work.
  12. [Electrical] +1 I like to use "fire" = start or tries to...

    +1

    I like to use "fire" = start or tries to start.
  13. [Electrical] The white/slate wire that fires the ignition coil...

    The white/slate wire that fires the ignition coil sounds like it may be a problem. That wire also goes to the tach, the RPM relay and the idle ECU. It comes from the ignition ECU and gets it's...
  14. [Electrical] Restart after a two hour stop points to loss of...

    Restart after a two hour stop points to loss of rest pressure if it was a hot day. On a cold day two hours should be enough time for the engine to cool down.

    Now the jumping tach would be another...
  15. Replies
    17
    Views
    574

    [Electrical] The 12 volt side that feeds the volt gauge comes...

    The 12 volt side that feeds the volt gauge comes from fuse #5 so make sure that fuse is clean. It may be some added loads on that circuit also may cause a voltage drop on the plus side. My car the...
  16. Replies
    17
    Views
    574

    [Electrical] Cutting the ground wire and moving it to the...

    Cutting the ground wire and moving it to the frame ground does not affect the operation of the inertia switch. It just moves the fuel pump ground current off the wire going to the gauges. The...
  17. Replies
    17
    Views
    574

    [Electrical] Yes moving the ground on the inertia switch to...

    Yes moving the ground on the inertia switch to frame ground will make your gauge read about 0.3 volts higher.
  18. Replies
    13
    Views
    725

    [Heat & A/C] That sounds pretty bad. I would guess you need a...

    That sounds pretty bad. I would guess you need a new compressor. What oil and refrigerant are you using.
  19. [General] Pressing the throttle will not flood the K-jet...

    Pressing the throttle will not flood the K-jet engine. All it does is open the throttle plates. There is no accelerator pump like in a carburetor. Was anything different like it sat for a week or...
  20. Replies
    50
    Views
    2,241

    [Engine] Great. A good running D with 5 speed will get...

    Great. A good running D with 5 speed will get that for highway mileage as long as your mostly in fifth gear.
  21. Replies
    31
    Views
    1,521

    [Fuel] This got off topic but here is a good articular...

    This got off topic but here is a good articular on the EVAP system in the Camry. Interesting they put the fuel pump pressure regulator in with the fuel pump so no return line is needed.
    ...
  22. Replies
    15
    Views
    512

    [Fuel] If it was a high pressure line you would get gas...

    If it was a high pressure line you would get gas flying everywhere. I bet your accumulator has failed.
  23. Replies
    31
    Views
    1,521

    [Fuel] I will have to look into it some more. The car...

    I will have to look into it some more. The car has been off for many hours and a pump noise will start and run for quite some time. I would think it has something to do with not venting gas fumes.
  24. Replies
    31
    Views
    1,521

    [Fuel] I think my 2018 Camry also checks for pressure...

    I think my 2018 Camry also checks for pressure build up. Every so often I hear a pump running many hours after a drive and i hear the pump near the fuel tank. I checked the internet about that pump...
  25. Replies
    26
    Views
    1,019

    [Electrical] Here is an interesting problem with...

    Here is an interesting problem with battery/alternator. Yesterday I was in a boat with an Mercuriser outdrive. The engine would cut (die) if the power tilt button was moved and the volt gauge was...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4