FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DMC5180

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. [Heat & A/C] There are no generic aftermarket condensers that...

    There are no generic aftermarket condensers that Iím aware of other than from DMC vendors. Stick with NOS or new remanufactured from a D Vendor.
  2. [Heat & A/C] Yes, 7 cylinder instead of 5. It operates...

    Yes, 7 cylinder instead of 5. It operates smoother and quieter. You almost donít notice when it cycles on and off, unlike the original SD508.
  3. [Engine] They donít require it. But some people like a...

    They donít require it. But some people like a belt and suspenders approach. Permatex great stuff is popular supplement that DMCMW uses in combination with the regular gaskets.
  4. Replies
    10
    Views
    472

    [Engine] Well done, Josh!

    Well done, Josh!
  5. [Heat & A/C] It kinda depends, I highly recommend the Sanden...

    It kinda depends, I highly recommend the Sanden SD7H15 series or UAC variant (mine). There are some considerations to think about. Are you replacing the 40 year old R12 hoses with new R-134 barrier...
  6. Replies
    5
    Views
    209

    [Brakes] Spray the area with ďbrake parts cleanerĒ or...

    Spray the area with ďbrake parts cleanerĒ or ďstarting fluidĒ both will wash away the fluid quickly and flash dry very fast. If the brake fluid reappears, you have your answer that the reservoir...
  7. [Engine] YAVOD (Yet Another Valley of Death) Teardown - Island Twin Turbo Edition

    Goo from the Alternator is a pretty good indicator itís done. Time for a replacement. Both of my Motorolas Original and replacement, eventually did that. I now have DMCH CS130 [emoji106]

    Be...
  8. Replies
    8
    Views
    278

    [Electrical] Make sure the bulkhead connection in the engine...

    Make sure the bulkhead connection in the engine bay is good. It never hurts to exercise the connections. It will help rub new contact areas in the terminals. Also look for pins that could be pushed...
  9. Replies
    8
    Views
    278

    [Electrical] New alternator not charging.

    A functional BATT light is required. I believe if you ground Brown/yellow wire, it will make the the light come on if the circuit is good. Iíll check the wire diagram to confirm though.

    Go to the...
  10. Replies
    8
    Views
    278

    [Electrical] New alternator not charging.

    Yeah, thatís typical when you get it from a D vendor. Like I said, it not required for the Alternator. The internal regulator are connected internally for the sense. Downside is that the external...
  11. Replies
    8
    Views
    278

    [Electrical] The brown wire was the 12V sense wire. If you...

    The brown wire was the 12V sense wire. If you had a pigtail harness plug for the new alternator with all the tails in it, you could connect it to the ďSĒ terminal. Itís technically not required...
  12. Replies
    24
    Views
    1,239

    [Engine] To me, the two pops sounded like it was coming...

    To me, the two pops sounded like it was coming from the intake.
  13. [General] +1 The average life of the Orange hose is...

    +1 The average life of the Orange hose is 10-15 years. Mine lasted about 20 before failing at the pump banjo fitting Pressure. Also the fuel pump boot may have failed under the cover. Mine failed...
  14. Replies
    24
    Views
    1,239

    [Engine] From the sound of the couple pops, it sound like...

    From the sound of the couple pops, it sound like itís out of time or incorrect ignition wire placement. Was the distributor removed?
  15. [Heat & A/C] Air blows hot with AC on, possible vents not switching?

    Hot water circulates through the heater core in All positions except MAX A/C. Verify Max A/C position does not allow heat. If it does you may have a faulty mode switch diaphragm. Also, reference the...
  16. Replies
    8,806
    Views
    1,926,646

    [General] My point of contact was the wire connector...

    My point of contact was the wire connector housing.
  17. Replies
    8,806
    Views
    1,926,646

    [General] I considered this. But as it stands I donít...

    I considered this. But as it stands I donít notice any additional vibration due to the current contact point.

    Hereís my clocking. Word of caution. Make the plastic cap for the Sender hole is...
  18. Replies
    8,806
    Views
    1,926,646

    [General] Iím not sure if the pump top on DPI pump is the...

    Iím not sure if the pump top on DPI pump is the same as what DMCH uses. With the DMCH pump, there was a sweet spot in the clocking where the interference was minimized. There was still contact,...
  19. [Fuel] [emoji106]

    [emoji106]
  20. [Fuel] Replaced Fuel Feed Line Now Car Wont Start

    Yes, If it started okay before you did this work, look for wire connections that may have been pulled loose while you were working in the area.

    1. Coil wire at Distributor
    2. Wire connection...
  21. Replies
    2
    Views
    520

    Custom Delorean build Artwork

    This is Amazing.

    https://hackaday.com/2021/05/18/tiny-delorean-made-from-lighters-is-a-total-gas/#more-476869

    Michael, this your next challenge. Iím sure you could wrap this with chewing gum...
  22. Replies
    4
    Views
    327

    [General] This is excellent that you were able to Identify...

    This is excellent that you were able to Identify them. Thatís half the battle. I suggest you post this in the RESOURCES Section call it Door/Roof harness connectors information.

    Could you also...
  23. Replies
    4
    Views
    327

    [General] You might want to contact Sales@britishwiring.com...

    You might want to contact Sales@britishwiring.com Email him a close up multiple view of the terminal with description of what itís from. If he doesnít have something he might be able to identify...
  24. [Engine] Did, you remove the idle air brass pipe the...

    Did, you remove the idle air brass pipe the enters the lower metering housing? If yes make sure the tube is actually inserted in the housing hole. Itís easy to think it was inserted put in reality...
  25. Thread: Knee pad studs

    by DMC5180
    Replies
    4
    Views
    718

    [Frame & Body] Just so you know itís not one stud. the M6 is...

    Just so you know itís not one stud. the M6 is threaded into the M10 threaded insert. You can get these type of inserts at a good hardware store. The might not have metric but you should be able to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4