FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    23
    Views
    312

    [Suspension] You can have an intermittent sticking brake...

    You can have an intermittent sticking brake cylinder. Next time it happens, stop and feel each front wheel. If it's sticking most likely that wheel will be hot.
  2. Replies
    23
    Views
    312

    [Suspension] Make sure both are tight. I don't remember the...

    Make sure both are tight. I don't remember the torque and not sure if there was a suggestion to double nut them.
  3. Replies
    23
    Views
    312

    [Suspension] Looks like your "anti-roll bar" the nuts are not...

    Looks like your "anti-roll bar" the nuts are not really seated in your photo. I expect you would see more of the bar threads.
  4. [General] I bought some anti-freeze today. Walmart is still...

    I bought some anti-freeze today. Walmart is still the best place at $10.88 gal for concentrated. I have had the otterstat pipe with the screw in otterstat for a few years now and figure it's a good...
  5. [Suspension] I don't think it's normal that splined contact...

    I don't think it's normal that splined contact moves much. The ball joints are what move when the distance changes. Is it normal high milage ones wear?
  6. [General] I was hoping to get my seat covers started but it...

    I was hoping to get my seat covers started but it looks like a long time to get the covers. They say there is no shipping working so I guess they make them in China.
  7. Replies
    129
    Views
    8,764

    I ran another test print with that new resin. I...

    I ran another test print with that new resin. I used larger supports but still lost a few during the print. So far I'm not happy using that new resin. I may try another resin someday.
  8. [Fuel] That's what I concluded from my testing. I've...

    That's what I concluded from my testing. I've though about using a controller on the fuel pump to reduce that fuel returned to the tank. Basically it would use a pressure sensor to reduce the pump...
  9. [Fuel] This is the thread on the pump I installed. So...

    This is the thread on the pump I installed. So far no problems but I have not made any long drives yet. I did do full testing of pressure and flow with great results. I also ran a very accurate...
  10. Replies
    129
    Views
    8,764

    Well I tried that new resin. It is flexible but...

    Well I tried that new resin. It is flexible but my test print was not a good choice. It looks like you need a lot more support. The bottom of my print pull off the supports during the print and...
  11. [Engine] Wait till you guys see my next design.:wrenchin:...

    Wait till you guys see my next design.:wrenchin:

    General Electric T58-GE03 gas turbine engine
  12. Replies
    63
    Views
    15,027

    I've not seen it change mixture much with...

    I've not seen it change mixture much with changing idle RPM setting. I guess it would depend on how good your FD is working. I have seen better more stable readings at higher idle RPM which I think...
  13. Replies
    31
    Views
    1,830

    [General] I don't really know what you mean but when I get...

    I don't really know what you mean but when I get my covers and tools I'm sure I will find out. I won't take the old ones off till I'm ready to start covering.
  14. Replies
    31
    Views
    1,830

    [General] Those look pretty heavy duty. They have to be...

    Those look pretty heavy duty. They have to be cutting steel hog rings.

    I ordered a set of hog ring pliers. They all looked pretty cheap so I just ordered on Ebay since Amazon seems to be slowing...
  15. Replies
    31
    Views
    1,830

    [General] What tools and supplies do I need to replace my...

    What tools and supplies do I need to replace my seat covers? This year my original drivers side cover has finally started to pull apart where the cracking in the leather was. It funny the passenger...
  16. [General] +1 Check that your bellcrank bolt is pivoting...

    +1

    Check that your bellcrank bolt is pivoting without play.
  17. [General] I wish my 2018 Toyota would let me select the...

    I wish my 2018 Toyota would let me select the gears. It does let you select the limit (highest gear) (It is an 8 speed). I like to drive to get the most MPG in that car and sometimes it takes to...
  18. [General] I never drove an auto D but every other car...

    I never drove an auto D but every other car selecting the lower gears that just prevents it shifting to a higher gear then you have selected and it will still use lower gears when necessary. It's...
  19. Replies
    129
    Views
    8,764

    Formlabs has a new resin that you can actually...

    Formlabs has a new resin that you can actually make some forms of springs in that you can bend it and it will return to original shape. I may buy this so I can play with it. I was reading up on the...
  20. Thread: Ground

    by Bitsyncmaster
    Replies
    9
    Views
    318

    [Electrical] There should be a capacitor (yellow wire) also on...

    There should be a capacitor (yellow wire) also on the + side of the coil. Your white wire should be white/yellow so I guess someone changed the wire.
  21. Replies
    1
    Views
    148

    [Electrical] The LED flasher should work fine with the front...

    The LED flasher should work fine with the front signal lights still incandescent. Basically an LED flasher has electronic timing as opposed to the old flashers that used the load to determine timing.
  22. Replies
    129
    Views
    8,764

    Formlabs has other resins that are more flexible...

    Formlabs has other resins that are more flexible and less brittle. I also see other vendors even have flexible resins for making gaskets or tires for your model cars etc. I look forward to trying...
  23. [Fuel] I had plans to do that but that box of parts are...

    I had plans to do that but that box of parts are still sitting in my garage. I got a junk mixture unit to do it also.

    But cut the banjo ends off your lines. I used a few to make my fuel pressure...
  24. Replies
    11
    Views
    424

    [Engine] I found my post about the step I had. Post #46 I...

    I found my post about the step I had. Post #46
    I had 0.016"

    http://dmctalk.org/showthread.php?16661-Clutch-replace/page5&highlight=step

    Also my flywheel had red locktite on the bolts. I used...
  25. Replies
    11
    Views
    424

    [Engine] If you still see the fly cutter cut marks on the...

    If you still see the fly cutter cut marks on the surface your flywheel should be fine. On mine all I did was sand it a little with 120 grit silicon carbide sand paper. I did the sanding on a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4