They may have changed but Delorean Go use to sell two versions of the motorized antenna (black and stainless mast). They both came with three motor wires: red, green, and black. Their instructions...
Type: Posts; User: DMC-Ron
They may have changed but Delorean Go use to sell two versions of the motorized antenna (black and stainless mast). They both came with three motor wires: red, green, and black. Their instructions...
I couldn't quite tell in the video if you done this already, but last summer I had to bleed my clutch slave and it was difficult to access the bleeder. If I had the access you now have, I would add...
On my car the antenna relay was the culprit which caused the antenna to stay in the up position. My relay is located behind the drivers seat under the rear deck (see photo). In order to retract,...
https://youtu.be/vXDUZpdSU_A?si=mgG6p9yQQk_DS1Kt
Headlight load is handled by the two relays (main beam relay and dip beam relay) so their current does not go through the switch contacts. However, current for all the other running lights does go...
Fair enough.
Tough Crowd.
Mike,
There's a subtle difference. In the photo on this thread, the blue/yellow wire (wire has been spliced and extended with a brownish wire) is connected with the white/red on the solenoid coil...
See attached diagram. Low Beam is relay 21. Fuse for low beam is number 14
Ron
69951
Mike,
Your measurement is likely correct. There are differences between different manufacturers on how they handle high/low beam. But one method used involves a slightly offset placement of LED...
Lars,
Normally the "low beam" indicator in the binnacle is directly powered from the low beam (dip) headlight relay circuit; meaning it gets the same power feed as the headlights. If the headlights...
Before drilling, I would suggest you first try using an 8-32 tap and see if you can rejuvenate the threads in the nutserts.
Ron
Perhaps a transition beyond the valley would be prudent?
Andy,
Having your battery voltage, settle to 12.5 volts after the engine turns off is pretty normal. If it sets for a few hours, it's not uncommon for the battery voltage to drop to 12.2 or so. ...
Andy,
I think both Nick and Dave are onto something. To assist, I?ve annotated a schematic with the 3 likely scenarios. If, in fact, the smaller gauge brown wire is connected to the two larger...
Andy,
What is the exact part number for the Bosch plugs. Do you happen to have a purchase link?
Ron
What AGM manufacture and model did you choose? I also have an old Interstate battery that's still working at 7 years but thinking about AGM.
Ron
Dave,
Those look good! If it turns out they wear through quickly and you're looking for another solution, perhaps modifying chair or cane silicone tips might be an option. There are small diameter...
Dave,
Maybe you have already checked this. After cranking pull a couple of plugs and see if they are wet or dry. Knowing if it's flooding, or starved ,helps focus the troubleshooting.
Ron
Owners often disconnect the wire from the second LH door plunger switch to stop the annunciator from buzzing when the door is open. The buzzer is obnoxious. The first plunger switch handles the...
Dan,
Usually a weakening magnet will not suddenly cause the speedo needle to not move. All speedo magnets slowly lose their magnetism over time. This usually results in the speedometer reading...
Just Googled DeLorean Parts Northwest and they did not show up. Only the real DPNW.
Dave,
Would it be possible to add a plug for a remote LED? Then we could have an indicator on an extension cord that we could see when working in the engine compartment.
Ron
Lars,
Consider doing a temperature test before installing the sensor. This is similar to what you might do when checking a thermostat. If you have a portable hot plate, pot with water, and...
I"m very pleased with this one. It's small and reads DC down to milliamps.
Ron
https://www.amazon.com/gp/product/B00O1Q2HOQ/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1
69262