FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Stainless

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Thank you. I'm not sure which route I want to...

    Thank you. I'm not sure which route I want to take. I do like the look of the gold/yellow in the engine bay as opposed to having everything with the polished metal look.

    As far as the POR15...
  2. How have the other areas, besides the valley,...

    How have the other areas, besides the valley, held up? I really liked the look of the gold high heat engine enamels of your engine bay (thread), but don't want to go down that route if it doesn't...
  3. Hey Dave - 10 years later, how have things held...

    Hey Dave - 10 years later, how have things held up? Have you been back into the valley to inspect the paint job?
  4. [Heat & A/C] A few months ago, I purchased a Sanden 4708...

    A few months ago, I purchased a Sanden 4708 compressor from Auto Air Online for around $240. It fits perfectly and looks very similar, if not identical, to the original, but much more shiny, of...
  5. [Wanted] I am. What's your definition of a "good one?"

    I am. What's your definition of a "good one?"
  6. [Wanted] 7+ years later... were you able to get your hands...

    7+ years later... were you able to get your hands on these? I'm in the market and not finding anything.
  7. [Wanted] Did you end up getting your hands on this? I'm in...

    Did you end up getting your hands on this? I'm in the market and finding nothing.
  8. Replies
    9
    Views
    654

    [Engine] I am using the Solary unit and it is large. I can...

    I am using the Solary unit and it is large. I can imagine that it may be too long or thick to use for hard to reach bolts. In my case, I have only had to use it on bolts that I have had clear access...
  9. Replies
    9
    Views
    654

    [Engine] Your understanding of how it works is correct....

    Your understanding of how it works is correct. The idea for me to use an induction heater is to use it in the prevention of broken bolts and studs. The other methods you mentioned are also very...
  10. [Engine] Should I just take it out of the car completely,...

    Should I just take it out of the car completely, or place it back on the frame where it was just sitting before? If it does no good just sitting there on the frame, I am inclined to take it out...
  11. [Engine] I'm not really sure how bad my studs are as I...

    I'm not really sure how bad my studs are as I haven't messed around with them yet as I've been focused on just getting the motor and transmission out of the car and separated. I didn't understand...
  12. [Engine] While we're talking about the studs that goes...

    While we're talking about the studs that goes through the aluminum lower block, mine appear to be seized, although I haven't taken a sledge to them to try and knock it free. They do appear to have...
  13. [Engine] Questions after pulling the motor and transmission

    The motor and manual transmission are officially out of my car, all started by me snapping an engine mount bolt in the frame. My "while I'm in there" list is growing at a rapid pace. Here are several...
  14. Replies
    15
    Views
    1,490

    [Engine] Well, after pulling the motor, I removed the...

    Well, after pulling the motor, I removed the crossover pipe and cat and was surprised at how good the cat looked on the inlet side. It was hard to get a good picture of the outlet side due to the...
  15. Replies
    9
    Views
    654

    [Engine] Induction heater for stubborn bolts

    I've seen an induction heater used several times by Davin on Hagerty's YouTube videos and couldn't find anyone that had mentioned this type of a tool on this forum. It can heat up a nut or bolt to be...
  16. Replies
    3
    Views
    2,212

    I gotta say that I removed my engine and tranny...

    I gotta say that I removed my engine and tranny together over the weekend and I found this write-up to be a tremendous help. My experience varied slightly since I have a manual transmission, but it's...
  17. [General] There are the 9 on the bottom, then the 3 on the...

    There are the 9 on the bottom, then the 3 on the edges near the top on each side that secure it to the fiberglass backing plate. I had one of those snap off as well, so I might as well replace that...
  18. [General] Surprising discoveries while removing engine

    As I'm going through the process of removing the engine and transmission from my car, I've discovered several things that I think my be unique as I start to take things apart.

    I found that I'm...
  19. Replies
    15
    Views
    1,490

    [Engine] Chunks fell out of muffler inlet

    When I removed my stock muffler, a pile of chunks fell out. I'm assuming these all came from the cat. What does this mean? Is my cat toast? Time for a cat delete? Is this the excuse I need to go...
  20. Replies
    0
    Views
    272

    [For Sale] Special T fuel pump and updated baffle

    I recently replaced my fuel pump with a Delphi unit, even though this pump worked flawlessly. It was bought from Special T Auto and installed by the previous owner in 2008 and has been in a running...
  21. Replies
    2
    Views
    334

    [For Sale] Sold

    Sold
  22. [Fuel] Well, rather than try to source an o-ring gasket...

    Well, rather than try to source an o-ring gasket locally, I chose to spend another $7 and buy an cap from DMCH. The o-ring was the correct size and my cap easily tightened down without issue. I'll be...
  23. Replies
    2
    Views
    334

    [For Sale] DMCH Defrost switch

    I accidentally bought two defrost switches, instead of one, to replace my original switch that has the defrost sign worn off, even though I've never used this switch. I bought it from DMCH for $39.95...
  24. Replies
    12
    Views
    2,707

    [Suspension] For those that are curious, I removed the leaking...

    For those that are curious, I removed the leaking shock today and found that Special T did just put a rubber or plastic wrap around the original markings. Here are the markings I found:

    66751 ...
  25. Replies
    6
    Views
    514

    [Electrical] Mine was the exact same wire. I'm going to see if...

    Mine was the exact same wire. I'm going to see if I can come up with a better way to keep that wire in place. If it worked its way loose once, it will probably happen again, eventually.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4