FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    40
    Views
    1,123

    So do I need to order the cleaner and post curing...

    So do I need to order the cleaner and post curing units? For what I'm planning you can not sand most areas to get a smooth finish so I don't see an FDM printer working for me. I can wash parts in...
  2. Replies
    3
    Views
    143

    [Engine] That does not look bad. You can use something to...

    That does not look bad. You can use something to clean it so you can see if any deep pitting has occurred. Where I saw deep pitting is on the outside where the hose is clamped.
  3. Replies
    4
    Views
    156

    You will find it is not worth the effort to...

    You will find it is not worth the effort to remove the old terminals. And if you just cut the wire flush you have something to reference what wires and wire colors should go to each new fuse.
  4. Replies
    15
    Views
    543

    [General] A mouse will find a way inside even with the...

    A mouse will find a way inside even with the doors shut. I do think your struts would last longer with the doors left open. There is a lot less tension on the bars with the doors open but not sure...
  5. [Electrical] A bad connection to the battery will react like...

    A bad connection to the battery will react like that. Had the same problem in a boat this summer. Volt gauge showed pegged at 20 volts but engine was running fine. Hit the power tilt and it killed...
  6. Replies
    16
    Views
    876

    I use a little shredded cheese. They seem to...

    I use a little shredded cheese. They seem to like the smell of sharp cheddar.
  7. Replies
    2
    Views
    122

    [Heat & A/C] If your compressor is making noise, it probably...

    If your compressor is making noise, it probably is low on "oil". Usually a leaking refrigerant does not loose much oil in the system. When you replace a component or flush it you need to add that...
  8. Replies
    40
    Views
    1,123

    Wow. That looks cool. Yes I just bought a...

    Wow. That looks cool. Yes I just bought a regular mouse. I will have to look at some reviews of that 3D mouse.
  9. Replies
    40
    Views
    1,123

    I ordered a mouse for my computer. Have not...

    I ordered a mouse for my computer. Have not needed a mouse since I lost my job 5 years ago. It looks like the FORM 3 printers have a 3 month ship delay. I'm still not ready to buy one yet anyway.
  10. Replies
    21
    Views
    787

    [Engine] Yes the tach, RPM relay, idle ECU and ignition...

    Yes the tach, RPM relay, idle ECU and ignition coil all connect to the ignition ECU output. The ignition coil has power on the plus side provided my the ignition resistors and the negative side is...
  11. Replies
    40
    Views
    1,123

    DesignSpark Mechanical

    This design program looks more like what I need. I don't need animation. I don't like the cloud software which seems to run very slow on my 20 MBit internet. I installed this program (takes about...
  12. Replies
    40
    Views
    1,123

    Can I 3D print over a "hole". I can flip the...

    Can I 3D print over a "hole". I can flip the project if printing over a hole is not possible.
  13. Replies
    21
    Views
    787

    [Engine] The RPM relay and idle ECU feed the ignition...

    The RPM relay and idle ECU feed the ignition signal into a pin which feeds a resistor and capacitor couples into the circuit. These components are inside the units. I assume the tach does the same...
  14. Replies
    21
    Views
    787

    [Engine] I would not think a broken tach would load the...

    I would not think a broken tach would load the ignition signal. All the ignition circuits I've seen have a resistor from the tach signal so only if that resistor shorted would it kill the ignition....
  15. Replies
    50
    Views
    1,420

    [Engine] Stock idle ECU is set to hold 775 RPM. I think...

    Stock idle ECU is set to hold 775 RPM. I think your RPM gauge should show close to that if the RPM is 775. You can put an external RPM gauge connected to the ignition coil.
  16. Replies
    40
    Views
    1,123

    Well I have tried about 7 CAD design software and...

    Well I have tried about 7 CAD design software and only the very basic "Tinkercad" let me get anywhere with a simple design. I then can import that into other software to get a little more checking. ...
  17. Replies
    16
    Views
    876

    Mouse trap

    This is a weird review but probably a lot of owners run across a problem with a mouse in your garage. Well so far I've trapped two of them in three days. I first tried the sticky pads but the mouse...
  18. Replies
    50
    Views
    1,420

    [Engine] My car is really sensitive on the adjustment. ...

    My car is really sensitive on the adjustment. You just turn the adjustment as small as you can and it moves about 10 deg. of change. So that small adjustment change is less than 5 deg of rotation...
  19. Replies
    50
    Views
    1,420

    [Engine] I would think your lambda ECU is working since...

    I would think your lambda ECU is working since you could get the min and max values from it. But it is weird to can not adjust the mixture also so maybe the ECU does have a strange failure. I do...
  20. Replies
    40
    Views
    1,123

    What I'm looking to create is a disk I can put...

    What I'm looking to create is a disk I can put text on. Sounds pretty simple but looks like I need to watch all the you tube training just to do that.
  21. Replies
    50
    Views
    1,420

    [Engine] +1 The PPR o-ring can go bad suddenly.

    +1

    The PPR o-ring can go bad suddenly.
  22. Replies
    40
    Views
    1,123

    I downloaded Blender. Holly Shi...t. That...

    I downloaded Blender. Holly Shi...t. That software is going to take forever to learn. It does things you really don't need to print a 3D part. I guess I don't think much about 3d since parts I...
  23. Replies
    21
    Views
    787

    [Engine] Injectors should not spray with the RPM relay...

    Injectors should not spray with the RPM relay jumpered not pressing the air plate. If they do you have your mixture adjusted wrong. You just want to back off the mixture adjustment so they don't...
  24. Replies
    50
    Views
    1,420

    [Engine] Poor compression would not cause you not able to...

    Poor compression would not cause you not able to adjust the mixture. It may change the mixture but the FD has a wide adjustment for mixture. Same if your lambda system was not working, you still...
  25. Replies
    50
    Views
    1,420

    [Engine] Pressure check is a good next step. If that...

    Pressure check is a good next step. If that checks out I would guess it's a problem with the fuel distributor. Try some injector cleaner in the gas tank to see if that helps.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4