Search:

Type: Posts; User: mr_maxime

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 40 minute(s) ago.

  1. Replies
    4
    Views
    186

    [Electrical] I had been told to do that in the past but didnt...

    I had been told to do that in the past but didnt know how. Guess this is what I was looking for:

    https://www.myodesie.com/images/wiki/2/V-Belt_Sheave_Alignment_edit.png
  2. Replies
    4
    Views
    186

    [Electrical] Water pump spins freely and stops when I let go.

    Water pump spins freely and stops when I let go.
  3. Replies
    4
    Views
    186

    [Electrical] Wear on alternator belt

    When checking belt tension this afternoon, I noticed a line where belt material had been getting thrown off the belt. I recently added DriveStainless's tensioner and I had to remove some washers...
  4. Replies
    6,933
    Views
    888,678

    [General] The DMCEU one from PJ Grady was $60 cheaper and...

    The DMCEU one from PJ Grady was $60 cheaper and comes with stainless hardware and bushings. It's also got the proper mounting points as well.
  5. Thread: Child seats

    by mr_maxime
    Replies
    17
    Views
    756

    The door opening is the bigger problem. I don't...

    The door opening is the bigger problem. I don't know what the standards were then, but that's the only way I can tell from the video that it would fail by modern standards. You don't want a poorly...
  6. Thread: Child seats

    by mr_maxime
    Replies
    17
    Views
    756

    I used to work in the crast test industry and we...

    I used to work in the crast test industry and we also did child seat testing. My 2 cents would be to wait until they are big enough not to require a car seat unless you are cruising on a closed...
  7. Replies
    35
    Views
    1,316

    [Electrical] I had a thread going but it got ruined by...

    I had a thread going but it got ruined by Photobucket
  8. Replies
    35
    Views
    1,316

    [Electrical] Yes, I removed the paint myself. I bought a...

    Yes, I removed the paint myself. I bought a delorean with the goal to mirror polish it, so I like it without the grain.
  9. Replies
    35
    Views
    1,316

    [Electrical] To be 100% clear about this, the PO was involved...

    To be 100% clear about this, the PO was involved in a literal fender bender which resulted in body filler being applied over the damage and the entire car painted. I sent pictures of the damage to PJ...
  10. Replies
    6,933
    Views
    888,678

    [General] Michael, I see your point. Looked more like a...

    Michael, I see your point. Looked more like a smudge to me.
  11. Replies
    35
    Views
    1,316

    [Electrical] ... I sanded the lff lol. The LFF is damaged...

    ... I sanded the lff lol.

    The LFF is damaged mostly beyond repair and I'm using it as a test piece for polishing the rest of the car. Hard to tell from this angle but it's mangled above the...
  12. Replies
    6,933
    Views
    888,678

    [General] I'm pretty sure the black part is bare plastic....

    I'm pretty sure the black part is bare plastic. You could sand it out yourself.
  13. Replies
    35
    Views
    1,316

    [Electrical] Look for them on ebay. got them much cheaper

    Look for them on ebay. got them much cheaper
  14. Replies
    35
    Views
    1,316

    [Electrical] https://i.imgur.com/buEQrgL.jpg?1

    https://i.imgur.com/buEQrgL.jpg?1
  15. Replies
    6,933
    Views
    888,678

    [General] What's up with that spot on the passenger side of...

    What's up with that spot on the passenger side of the rear fascia???

    EDIT:Totally not nitpicking because your car looks nicer than mine
  16. Replies
    31
    Views
    2,017

    Having purchased a painted car here are some tips...

    Having purchased a painted car here are some tips from me. Unscrew the marker lights and CAREFULLY feel around the hole. If there was damage, there is a good chance they wrapped the body filler...
  17. Replies
    35
    Views
    1,316

    [Electrical] I had two buckets out at once, so they ended up...

    I had two buckets out at once, so they ended up getting swapped. if you look you'll see a number marked at the top of each bucket.

    Pic in this post, left is LED and right is old HID...
  18. Replies
    35
    Views
    1,316

    [Electrical] The mistake I made is not realizing that the low...

    The mistake I made is not realizing that the low beam and high beam buckets are actually different. There is a larger notch in the upper left corner of the high beam for it to sit in. Didn't make...
  19. I've wondered what the rim would look like and if...

    I've wondered what the rim would look like and if itd be easier to clean with every other fin was machined off, but I just tried photoshopping it and it looks like there are an odd amount of fins...
  20. Replies
    12
    Views
    750

    Just got a tropical storm warning this morning...

    Just got a tropical storm warning this morning saying that I am now in Irma's path. Should be a tropical storm when it hits.
    ...
  21. Replies
    6,933
    Views
    888,678

    [General] Installed the new LED headlights, finally scraped...

    Installed the new LED headlights, finally scraped all of the overspray of my windows, and used panel bond to attach stainless bolts to the front spoiler.
  22. Replies
    35
    Views
    1,316

    [Electrical] Also, these still didn't sit perfectly. I had to...

    Also, these still didn't sit perfectly. I had to take the front fascia off to get them to sit properly.

    https://i.imgur.com/6tcQPtF.jpg?1
  23. Replies
    35
    Views
    1,316

    [Electrical] Well after cutting the bucket to fit and putting...

    Well after cutting the bucket to fit and putting the headlights back on, I noticed a major mistake... I cut the high beam bucket. I didnt realized the notches varied.
    https://i.imgur.com/IkYbFwT.jpg
  24. Replies
    35
    Views
    1,316

    [Electrical] Reinforcement is done. h4 is properly wired. All...

    Reinforcement is done. h4 is properly wired. All I need to do is chop the bucket up to get the headlight in and splice a spade terminal into the marker lights for the demon eye.

    I just don't want...
  25. Replies
    35
    Views
    1,316

    [Electrical] Well I could easily get some LED H4 bulbs, but...

    Well I could easily get some LED H4 bulbs, but I'm not pleased with the light pattern with the semi-sealed 4x6 headlights.

    These are the ones I got...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4