Search:

Type: Posts; User: DMC5180

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6,933
    Views
    888,768

    [General] What have you done to your DeLorean today?

    Had a hard time reading this. You can blame it on Auto-correct. [emoji6] I filled in the missing words with what I believe you intended to say.

    ďMy car had one of his on IT and the Fan started to...
  2. [General] Lowest attendance of cars shown on DSC Saturday...

    Lowest attendance of cars shown on DSC Saturday was 42 at Orlando. As I recall the banquet/ cars show hall was to capacity. I donít think you could have squeezed another car in. Then space was also...
  3. Replies
    46
    Views
    2,163

    [Heat & A/C] Refurbing a Very Early A/C System

    Thanks for the added info.

    At some point this thread needs to be placed in the How To Section. Great detail write ups and photo documenting. Granted most folks would not go through the tear down...
  4. Replies
    6,933
    Views
    888,768

    [General] Cool, maybe it was Josh. Heís in Ragina,...

    Cool, maybe it was Josh. Heís in Ragina, correct? Does the flatter front give you enough clearance so you donít have to cut onto the closing panel?
  5. Replies
    6,933
    Views
    888,768

    [General] What are the notable configuration differences in...

    What are the notable configuration differences in the LS4 vs what Jonathan and Nick used?
  6. Replies
    46
    Views
    2,163

    [Heat & A/C] Dana, It seems like you skipped over the part...

    Dana,

    It seems like you skipped over the part of piston and swash plate reassembly. Did you replace the Rings? I assume the pistons and cylinder bores showed no signs of wear.
  7. Replies
    6,933
    Views
    888,768

    [General] That would be nice, if the transmission could...

    That would be nice, if the transmission could handle it.
  8. Replies
    6,933
    Views
    888,768

    [General] What have you done to your DeLorean today?

    If you say so! [emoji57]


    Anyway, what is the target HP you are shooting for.
  9. Replies
    6,933
    Views
    888,768

    [General] That image seems a bit inappropriate. Just sayin...

    That image seems a bit inappropriate. Just sayin [emoji12]
  10. [General] Traditionally, the Belfast expo happens in 5 year...

    Traditionally, the Belfast expo happens in 5 year intervals. The next would be in 2021 if it happens.
  11. [General] Thatís your story and your sticking too it ....

    Thatís your story and your sticking too it . [emoji6]
  12. Replies
    296
    Views
    31,513

    What did you do to the upper cable to make it...

    What did you do to the upper cable to make it work? Were the input/outputs a square drive or round with a tang slot?
  13. [General] I answered the question, thatís what! [emoji4]

    I answered the question, thatís what! [emoji4]
  14. [General] Rob Grady

    Rob Grady
  15. Replies
    296
    Views
    31,513

    If the spindle cable fails, itís typically caused...

    If the spindle cable fails, itís typically caused by the angle drive gears wearing out and occasionally locking up. This assumes the rest system upstream is well lubricated relatively friction free.
  16. Replies
    296
    Views
    31,513

    3.0L engine swap

    Fair enough.

    if Iím not mistaken, i think youíre configuration is similar the Hervey headlight switch saver fix. Except that in his version, the OE headlight switch is still used for the dual...
  17. Replies
    296
    Views
    31,513

    It should work. Iím kind a curious why youíre...

    It should work. Iím kind a curious why youíre opting for this vs the ďlogic boxĒreplacement DMCH switch.
  18. Replies
    296
    Views
    31,513

    3.0L engine swap

    So in your schematic, you are using the single position on/off hazard switch to operate the headlight Feed to the main or high beam relays, while also adding a new relay to operate park/tail/marker...
  19. Replies
    10
    Views
    465

    [Frame & Body] The Nos Thin grey stripe should be just fine as...

    The Nos Thin grey stripe should be just fine as long as the release film is still stuck to the adhesive of the stripe. An NOS wide black stripe might have problems though. I have NOS examples of both...
  20. [General] Also the heater core lines donít flush out...

    Also the heater core lines donít flush out naturally either. Technically, you would need to disconnect the lines where they attach to the engine. Then connect extension hoses to the lines too clear...
  21. Replies
    6,933
    Views
    888,768

    [General] Sounds like a real barn find.[emoji12]

    Sounds like a real barn find.[emoji12]
  22. Replies
    22
    Views
    1,922

    [Frame & Body] I looked at one for visual comparison to the GO...

    I looked at one for visual comparison to the GO seal. The Go seal is still a smaller profile. I donít have any noticeable air leaks that I can distinguish the typical road noise Iím accustomed too.
  23. [General] Need advice. I just inherited a 1981 Delorean with 1,248 miles. Been in dry storage

    Actually I normally use Custom application, especially if its a new kid. Iíd rather not get into a discussion about the Delorean.
    This is only when I need to visit an auto parts store other than my...
  24. [General] Be advised that the Cross-reference parts list...

    Be advised that the Cross-reference parts list was compiled mostly back in the 80's through the owners club network to help owners with service parts during the period of uncertainty. (83-95) Pre...
  25. Replies
    22
    Views
    1,922

    [Frame & Body] Door seal installation help

    I switched to the Delorean Go seals, no more issues and donít keep them wiped with silicone.

    Incidentally, I installed them this spring when I first heard about them.

    When I went to the DMCMW...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4