FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Rhye

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    3,563

    I'm sorry but the interest in mirror switches is...

    I'm sorry but the interest in mirror switches is so (unexpectedly) high that my (soon coming, hopefully) preproduction lot (4 pcs) is already reserved. If everything goes well with the project and if...
  2. Replies
    35
    Views
    3,563

    First of all, I decided to extend my test...

    First of all, I decided to extend my test programme and added 10 000 cycles (20k if you count both directions) in room temperature environment (22 deg C). So far, the switch completed a total of a...
  3. Replies
    35
    Views
    3,563

    @ D Knight It should be also fairly easy to...

    @ D Knight

    It should be also fairly easy to MJF 3D-print the switch caps with decal cut-out. I'll probably give it a try and design/order one sample cap along with next batch of mirror switch...
  4. I've got one important note to share with all...

    I've got one important note to share with all do-it-yourselfers - please take a look at the front PCB layout from page no. 2 of my manual:

    61311

    All those circled areas look like PCB pads...
  5. Replies
    35
    Views
    3,563

    Coming back to the mirror switch project: I've...

    Coming back to the mirror switch project: I've just finished a test bench and endurance test has already begun. I expect first results late next week. Wish me luck. :)

    61309
    ...
  6. Replies
    2
    Views
    285

    [Wanted] Renault Alpine A310? :)

    Renault Alpine A310? :)
  7. Replies
    35
    Views
    3,563

    No jumpers on the board - these loops are just...

    No jumpers on the board - these loops are just wires pulled through the holes in PCB to the other side (to prevent bare copper strands bending). The transistor-like component is a constant current...
  8. [Wanted] What kind of filament is it made of?

    What kind of filament is it made of?
  9. Replies
    33
    Views
    5,371

    [Frame & Body] Seems feasible to 3D-print it, even in cheapest...

    Seems feasible to 3D-print it, even in cheapest FDM technology. I can prepare and post 3D model of the part, if anybody's interested.
  10. Replies
    35
    Views
    3,563

    Thank you all for the positive feedback on the...

    Thank you all for the positive feedback on the project. I'm progressing very slowly now since I'm mostly focused on reproducing front end of my crashed D body.

    @ Mark D
    You're first on the...
  11. Replies
    7
    Views
    422

    [Electrical] Brake fluid level too low? Or a faulty level...

    Brake fluid level too low? Or a faulty level switch.

    IMHO, loose wire would mean no brake light at all - unless it touches vehicle's ground somewhere.
  12. Replies
    17
    Views
    1,075

    [Heat & A/C] I've created a 3D model of the actuator arm...

    I've created a 3D model of the actuator arm optimized for FDM 3D printing, just in case one want's to recreate the part. Metal rod has to be fabricated according to the drawing and glued in. These...
  13. Replies
    17
    Views
    1,075

    [Heat & A/C] OK, clear. So if the arm of the actuator itself...

    OK, clear. So if the arm of the actuator itself is broken, then the question is if it's possible to take the actuator apart and replace the arm with reproduced part - can't recall how it's made but I...
  14. Replies
    17
    Views
    1,075

    [Heat & A/C] My parts catalogue says 105068, but that's the...

    My parts catalogue says 105068, but that's the same part.

    60321
  15. Replies
    17
    Views
    1,075

    [Heat & A/C] If you mean lever P/N 105068, then I think it can...

    If you mean lever P/N 105068, then I think it can be easily 3D printed using inexpensive FDM technology, with some minor changes to improve strength (FDM part is always slightly weaker than injection...
  16. Replies
    35
    Views
    3,563

    As for me, nothing for sale at the moment. And...

    As for me, nothing for sale at the moment. And I'll always need my OEM switch as a master part.
  17. Replies
    35
    Views
    3,563

    After some noticeable delay (: in design...

    After some noticeable delay (: in design finishing (had to focus on another urgent project in the meantime), prototype mechanical parts arrived finally. Here are the results:

    Prototype #1...
  18. Replies
    35
    Views
    3,563

    No, it will be totally different animal inside -...

    No, it will be totally different animal inside - PCB with some standard electronic components will be used.

    If there's some need for spare parts for original switch, I could check if it's feasible...
  19. Replies
    35
    Views
    3,563

    Final parts (and the two soon coming prototypes)...

    Final parts (and the two soon coming prototypes) will also be 3D-printed, but in totally different technology than the FDM pre-proto part. Surface finish will be like on the sample close-up attached...
  20. Replies
    35
    Views
    3,563

    Reproduction mirror switch project

    Hi everybody,

    I'm currently running a reproduction mirror switch project and decided to share it with the community since I guess at least some of you may find it interesting. The switch will be...
  21. OK, so here is my very rough idea on displaying...

    OK, so here is my very rough idea on displaying "AUX" letters:

    57430

    The circuit consists of 2 IC's, 9 transistors, 10 diodes, 17 resistors and 3 capacitors. PCB would need to be designed and...
  22. One important correction/clarification to my post...

    One important correction/clarification to my post above: you can only display single letter (or a set of 3 identical letters - which is useless :| ) using the method I've described! I'd suggest to...
  23. Yes, I've even made some research into displaying...

    Yes, I've even made some research into displaying AUX when preparing this mod, but decided not to do it 'cause it's quite a lot of additional wiring. Besides, I thought that a single dolby LED is...
  24. Replies
    28
    Views
    3,190

    [Frame & Body] That's perfect - no more questions. (: So...

    That's perfect - no more questions. (:



    So an (almost) open source 3D printer (: - this sound's much better.
  25. Replies
    28
    Views
    3,190

    [Frame & Body] Had no idea they use GPL licensed software in...

    Had no idea they use GPL licensed software in commercial products - this sounds ridiculous.



    No problem at all to change orientation of the part before exporting to STL. I had something else on...
Results 1 to 25 of 38
Page 1 of 2 1 2