FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: dmcman73

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. [Engine] I figured, but it seems that having it under...

    I figured, but it seems that having it under (between the intake and bracket) would give it a better ground connection.

    Thanks!
  2. [Engine] So I assume that the ground wire gets mounted...

    So I assume that the ground wire gets mounted under the original brackets top mount?

    Thank you!
  3. [Engine] Ground wires and Idle speed motor support bracket

    I a just getting around to reassembling my intake manifold and I had asked another Delorean owner where a bindle of grand wires went that came off of the look with the WUR and Cold Start valve...
  4. That would be great! How much?

    That would be great! How much?
  5. @Josh, When you had your 3.0 engine, did you...

    @Josh,

    When you had your 3.0 engine, did you use a Jeep throttle body attached to the air intake of the 3.0 using a custom adapter plate? Was there a reason you didn't use the throttle body that...
  6. [Fuel] I agree about the hoses. When I purchased my...

    I agree about the hoses. When I purchased my aftermarket Tahoe pump, I used standard nylon fuel lines for the pump.
  7. It's a "dumb" cam mounted to the timing cover.

    It's a "dumb" cam mounted to the timing cover.
  8. OK, looks like I'm now leaning more towards an...

    OK, looks like I'm now leaning more towards an MS3...lol

    Is your engine a stock 2.8 converted to EFI or an Eagle 3.0? If it's the Eagle 3.0, are you using the stock injectors for it or did you go...
  9. Some good info here, thanks! I already knew...

    Some good info here, thanks!

    I already knew about the 3.0 and the 3.57 board differences (through hole VS SMD); through hole components are easier for most to assemble. I wish they offered the SMD...
  10. Iím an electronic tinkerer as well, but, I just...

    Iím an electronic tinkerer as well, but, I just want to install something, get it tuned and forget about it.
  11. Replies
    25
    Views
    1,456

    This is the actual engine, looks like it's...

    This is the actual engine, looks like it's without the distributor 63918

    It's coming out of a 1988 Eagle Premier.
  12. Replies
    25
    Views
    1,456

    I'm actually going to be doing this for an Eagle...

    I'm actually going to be doing this for an Eagle Premier 3.0 engine. I just purchased a low mileage engine and waiting for it to come in. Can I still use the stock ignition or do I need to setup the...
  13. Replies
    25
    Views
    1,456

    I'm actually leaning towards the Microsquirt as...

    I'm actually leaning towards the Microsquirt as well. I'm not looking to do anything fancy with the setup, just simply control Fuel and Spark, cooling fans and to be able to reliably control the A/C...
  14. Replies
    25
    Views
    1,456

    I am planning on doing the same engine swap in my...

    I am planning on doing the same engine swap in my car within the next year, what route did you go in regarding the Megasquirt / Microsquirt model?
  15. Thanks! I am still in the planning and designing...

    Thanks! I am still in the planning and designing stages as of now so I haven't decided on which one to start with. But this was all very helpful!
  16. What does the v3 offer over the v2 when using it...

    What does the v3 offer over the v2 when using it on the Eagle 3.0 engine?
  17. Megasquirt question for Eagle 3.0 conversion

    Hi all,

    I found a 3.0 engine that I am waiting for delivery on and I had a question that I could not find on the forums. I see that most of the Eagle 3.0 engine swaps are using the MS2 3.57, is...
  18. Replies
    28
    Views
    7,447

    [Engine] Thanks for the quick reply! So no issues with the...

    Thanks for the quick reply! So no issues with the new aluminum that was applied to the block during the process, nothing peeling away? Good luck with the rebuild!
  19. Replies
    28
    Views
    7,447

    [Engine] Hi Shane, sorry for reviving an old post, but,...

    Hi Shane, sorry for reviving an old post, but, since you had this done a few years ago, how has it been holding up on your engine block?
  20. Replies
    9
    Views
    547

    [Engine] Awesome, thanks!

    Awesome, thanks!
  21. [General] Not for a while, still restoring my car and I...

    Not for a while, still restoring my car and I have to send the wheels out to get refinished first. Maybe within the next few months.
  22. Replies
    9
    Views
    547

    [Engine] Thanks! I was also told that the block needed...

    Thanks!

    I was also told that the block needed some substantial machining to adapt the DeLorean heads to the block mating surfaces, is that true?

    Any information you can provide about swapping...
  23. Replies
    9
    Views
    547

    [Engine] Are there any other differences? Does it still...

    Are there any other differences? Does it still have to plug at the top of the engine for TDC like the DeLorean one has? No threading issues (I've read else where that the threads in certain places...
  24. [General] I just received these tires from Tirerack. The...

    I just received these tires from Tirerack. The rears do indeed have the raised white lettering on one side and black on the other. The fronts are only raised black.
  25. Replies
    9
    Views
    547

    [Engine] Engine block replacement?

    Hi All,

    Does anyone know if the engine block from a 1988 Volvo 760 (I believe its a B280f?) can be a direct replacement for the Delorean's engine block?

    I need to replace the engine block on my...
Results 1 to 25 of 29
Page 1 of 2 1 2