Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    373
    Views
    83,820

    You will need to remove the linkage brackets to...

    You will need to remove the linkage brackets to clear the water pipes. Yes 4 bolts on the transmission to engine, 3 starter bolts and if you have the plate covers those come off (mine had no...
  2. Replies
    7
    Views
    230

    [General] I will put a long software timing to average the...

    I will put a long software timing to average the sensor readings. I may think of some ways to average that work better. When you first turn the car on it will quickly show what the sensor reads and...
  3. Replies
    7
    Views
    230

    [General] It would be nice to get resistance readings of...

    It would be nice to get resistance readings of senders that are installed. The full reading is normally what the manufacture states since the float is maxed out (unless the float arm is bent). The...
  4. Replies
    7
    Views
    230

    [General] I ordered a few prototype circuit boards for my...

    I ordered a few prototype circuit boards for my design. What I have come up with are adjustments (trim pots) to calibrate the gauge and tank sender. Things may change after testing and software...
  5. Replies
    11
    Views
    349

    [General] Magic tire balancing

    Magic tire balancing. Is this real or just BS?

    https://www.sherco-auto.com/balancing-beads.html
  6. Replies
    4
    Views
    130

    [Fuel] Mine holds almost three hours. I think my hot...

    Mine holds almost three hours. I think my hot start relay may help you but it would still take one second of cranking for it to kick on the CSV.
  7. Replies
    7
    Views
    230

    [General] New Fuel Gauge Circuit

    After prodding from a few owners, I decided to start a fuel gauge circuit design. I’ve come to accept that car fuel gauges are inaccurate in that when you fill up, the gauge shows above the full...
  8. [Electrical] Yes you would need to cut the ground wires on the...

    Yes you would need to cut the ground wires on the side lights and attach those side light wires to my board. The neatest way to make the connections is to unwrap the OEM harness and make the ground...
  9. [Electrical] I'm pretty sure all you need to do is cut into...

    I'm pretty sure all you need to do is cut into the harness and splice there. Now if you want to make connections by crimping two wires into connector pins then you would need access to the headlight...
  10. [Electrical] When you pull the front "grill" you have easy...

    When you pull the front "grill" you have easy access to all the harness.
  11. Replies
    150
    Views
    5,943

    [Transmission 5-Speed] Yes vendor is correcting it. I ended up...

    Yes vendor is correcting it. I ended up rebuilding my old axle to replace it. I'm assuming someone sent in an axle from another car which happens to be shorter. I think I read some people think...
  12. Replies
    7,540
    Views
    1,107,157

    [General] Took my car out for a road test today after I did...

    Took my car out for a road test today after I did my clutch replacement.

    Backed out of my driveway and could not get it out of reverse. Turned out my clutch needed to be bled again.

    Then I...
  13. Replies
    4
    Views
    261

    Your problem is probably noise getting into the...

    Your problem is probably noise getting into the circuit you use to input the signal to read RPM and cam location.

    Make sure your signal grounds and shields don't conduct current. So those grounds...
  14. Replies
    150
    Views
    5,943

    [Transmission 5-Speed] Done

    Well it turned out my one new axle may have cause my problem. When I pulled the axle I noticed one boot had pulled off the flange end. Well when I was going to put the axle back in I noticed one...
  15. Replies
    21
    Views
    521

    [Electrical] Make sure the headlight relay sockets have all...

    Make sure the headlight relay sockets have all pins seated in the socket. Sometimes a pin gets pushed out of the socket when inserting the relay.

    You can make up a jumper wire and test the...
  16. [Engine] There is no adjustment for the cold engine dwell....

    There is no adjustment for the cold engine dwell. Those values of cold and with WOT closed are preset values build into the lambda ECU.
  17. [Engine] I don't think 80 C is a correct value. I hardly...

    I don't think 80 C is a correct value. I hardly ever see 54 deg (60%) duty only in sub freezing weather.
  18. Replies
    14
    Views
    605

    [Fuel] You could file or sand any sharp edges off a...

    You could file or sand any sharp edges off a barbed fitting and result in more of bead.
  19. Replies
    19
    Views
    594

    [General] It seems the DeLorean torque spec of 30 ft/lbs is...

    It seems the DeLorean torque spec of 30 ft/lbs is light. Recommended torque for a 10 mm 8.8 bolt is 40 ft/lbs. dry. I know some people are using locktite but that was not stock from factory. I...
  20. Replies
    8
    Views
    209

    [Electrical] If your blower breaker has 4 wires on it you...

    If your blower breaker has 4 wires on it you probably have the mod.

    Your VIN is late enough that it should have been modified.
  21. Replies
    10
    Views
    414

    Looks like only 4 of the 18 fuses go to battery...

    Looks like only 4 of the 18 fuses go to battery power. Four go to one AUX relay. Three go to the other AUX relay. The rest have non battery connections to both sides of the fuse. So your looking...
  22. Replies
    8
    Views
    209

    [Electrical] If you have the starter relay mod installed. ...

    If you have the starter relay mod installed. Just pull that relay and jumper the two terminals (row of three, the ends).
  23. Replies
    10
    Views
    414

    Depends where you mount it if all the existing...

    Depends where you mount it if all the existing wires would be long enough. Then you need to make your own wire list to document what you did.
  24. Replies
    10
    Views
    414

    Unless it comes with a complete harness, you...

    Unless it comes with a complete harness, you still need to make all the connections.
  25. [Engine] You would need to make that wiring change to use...

    You would need to make that wiring change to use a standard relay or my relay.

    I also use my relays for replacing the AUX relays but had to put new pins on the wires since the OEM relays used...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4