After years of work, a lot of fun drives, sweat, tears, and elbow grease, VIN 1659 is running in the best shape it's ever been, so it's time for me to sell. I worked with the Bring-A-Trailer folks to...
Type: Posts; User: kdumont
After years of work, a lot of fun drives, sweat, tears, and elbow grease, VIN 1659 is running in the best shape it's ever been, so it's time for me to sell. I worked with the Bring-A-Trailer folks to...
Found it! Thanks so much.
Hey all, I'm finally getting the pieces all back together from a VoD cleanup that's taken far too long!
I can't figure out where to terminate the frame ground points on the rear (right by the rear...
I'm gearing up to do some more work on the delorean this summer, since I wasn't able to get it back to running last fall. My last thread was here:...
It's been a lot of planning and cleaning, but finally making some progress. Here's the latest with...
- Y-pipe reinstalled
- new coolant reservoir installed
- new water pump
- all new...
Do these gaskets (or others) require gasket seal, like permatex? Can't seem to find that documentation.
Thanks, yeah I had to call around a LOT to find a place that would do small batch zinc plating - had to drive down to MA because apparently you can't do that plating work in NH due to regulations.
...
Just wanted to update this thread. I've completed my teardown and after 10+ hours of cleaning and scrubbing...
I've gotten from this:
67170
To this, painted with PoR 15 Engine Enamel:
67171
...
Got it! If it's leaking goo, time to renew.
This is super neat. I was going off Dave's notes and ordered stainless clamps. Was planning on pressure testing before building everything back up,...
Earlier this spring I turned over my DeLorean for the first time since early winter (went through some steps to winterize, like eth-free gas) and was greeted with coolant sludge pouring out of the...
While pressing the hub onto the spindle. Essentially the inner shaft of the bearing started to slip out - I caught before it came out completely and pushed it back in.
Thanks for the tips everyone! I got the brakes together yesterday. I ended up splurging and going with the vented rotors from Delorean Go & EBC red, low dust brake pads, though in retrospect I...
As you suspected, one of the caliper pistons on the right side was totally stuck. I took the caliper off and broke it down - it was quite a mess.
Actually to pry the jammed piston out I had to...
Yeah, as you can see in the photo above there's still a lot of life left in there, whereas the right pads are down to the back-plate. That was my concern when I realized those pads wore down so...
Just checked out the left brake and pads look almost new. There is gunk around the bleeder valve.
64805
So, I sadly wore through my front right brake pad recently. Unfortunately, I was an hour away from home when I realized it. By the time I got back I had gouged the rotor pretty badly (Fortunately, I...
I was able to fix the windshield washer pump. It actually ended up that the contacts were slightly corroded and not making a full connection. This was actually a good thing because when I took the...
Thanks for the help! I took out the windshield washer reservoir and it was full of black gunk. I'm going to soak it in a vinegar solution for a little bit. Otherwise it looks fine. I took the pump...
It's been a while since I posted, but I have the DeLorean out of the garage for a few more projects.
Last year I had the speedometer/odometer fail on me while out on a drive. I replaced the...
I want to update everyone on the from my previous thread a couple years ago:
http://dmctalk.org/showthread.php?10146-New-DeLorean-Owner-Advice
I ended up bringing the car to a local mechanic I...
I choose #1, ha
Ha, thanks. I certainly agree with this. I actually have a covered location to move it to now. There's also a ?custom? fit car cover over the exterior, so damaging the finish isn't as much of a...
Thanks guys. All-in-all, it reaffirms my decision to get it roadworthy and insured. That writeup on replacing the coolant is great. I will definitely check it out.
Hi David, I'm going to play around with car over the course of the summer. For what it's worth, I was driving the car around the block last fall without any issue. I'm going to replace the fluids and...
I appreciate the response. There was not much mileage on the existing tires, and they've been in a garage for ~15 years. They were oiled about once a year, but I would say it's at any buyer's...