Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    6
    Views
    324

    [Engine] That looks like the CAT is glowing. Have you...

    That looks like the CAT is glowing. Have you checked that your lambda is working and set correctly?
  2. Replies
    29
    Views
    1,016

    [Fuel] Hervey had a kit also. I've looked for bulk buy...

    Hervey had a kit also. I've looked for bulk buy but could not find any good deals. I bought a bunch from McMaster-carr but they are still pricey for just being a copper washer.
  3. Replies
    7,114
    Views
    945,638

    [General] i use wheel bearing grease on bolts to help...

    i use wheel bearing grease on bolts to help prevent corrosion. It is very thick and should not wash off.
  4. Replies
    30
    Views
    4,328

    [General] I've been giving the fan fail a lot of thought. ...

    I've been giving the fan fail a lot of thought. The problem with checking low current is it shows problems with marginal connections which most users don't have the ability to fix. The OEM fans do...
  5. Replies
    12
    Views
    361

    [Engine] I'm pretty sure the resistor terminals are...

    I'm pretty sure the resistor terminals are stainless steel since I could not solder the wires to them.
  6. Replies
    12
    Views
    361

    [Engine] The two white "tubes" on the firewall in the...

    The two white "tubes" on the firewall in the engine compartment on the drivers side. There are about four wires that clip onto those resistors that you need to be sure are tight. Just pulling each...
  7. Replies
    12
    Views
    361

    [Engine] If it dies when you let off the start position,...

    If it dies when you let off the start position, your resistor connections are probably bad.
  8. Replies
    317
    Views
    38,445

    Here is one write-up: ...

    Here is one write-up:

    http://dmctoday.com/showthread.php?531-Spec-01-Steering&highlight=spec+01
  9. Replies
    30
    Views
    4,328

    [General] I've decided to stop sales of my electronically...

    I've decided to stop sales of my electronically fused fan fail unit. I designed this unit because the fuses produced so much heat when an owner was still using OEM fans. But after many sales it...
  10. The motor drive is very noisy but I don't think...

    The motor drive is very noisy but I don't think it will be run much. Pretty much only fall and spring is when I need heat, otherwise it will remain closed.
  11. My valve has a geared motor on it so it stays...

    My valve has a geared motor on it so it stays open or closed without power. It takes very little current when the motor runs but it was just a little to big to fit up front. I may be able to fit it...
  12. Your replacing the heater valve with an...

    Your replacing the heater valve with an electrical one and making it shut with temp set to cold is the same idea I had. I bought the valve but found it to large to fit up front. I still have it but...
  13. Replies
    3
    Views
    208

    [Suspension] Those split collars just sit on a circular ring...

    Those split collars just sit on a circular ring and the cup keeps the collars together. So when you pull the shock and spring it just lifts up.
  14. Replies
    7,114
    Views
    945,638

    [General] That gasket is probably nylon to also reduce the...

    That gasket is probably nylon to also reduce the friction when you need to adjust the ride height.
  15. Replies
    41
    Views
    674

    [Engine] There have been some idle ECU failures. It's...

    There have been some idle ECU failures. It's mostly the transistors that drive the ISM that fail. If your ISM gets a short circuit then that will probably blow the drive transistors. I don't...
  16. Replies
    6
    Views
    246

    [Electrical] Volt gauge can be checked with a voltage source...

    Volt gauge can be checked with a voltage source up to 15 volts. I would not check the other gauges on the sensor side with a wall-wort. Most wall-worts don't have electronic current limiting or it...
  17. Replies
    41
    Views
    674

    [Engine] Yes history would help. If you have one of my...

    Yes history would help. If you have one of my idle ECUs, it does not buzz the ISM when the key is turned on. Mine would have a blue wire coming out between the two connectors or you could have an...
  18. Replies
    41
    Views
    674

    [Engine] I have a few OEM units I have not updated yet. I...

    I have a few OEM units I have not updated yet. I also have my updated units for sale. If you just want to test the ECU I can send you one for the price of shipping but you would need to return it...
  19. Replies
    41
    Views
    674

    [Engine] Can you borrow one from another owner? Have not...

    Can you borrow one from another owner? Have not heard of any bad solder joints with the idle ECU (it does not get that hot and has conformal coating sprayed on the circuit board).
  20. Replies
    41
    Views
    674

    [Engine] Try unplugging the 4 pin connector on the idle...

    Try unplugging the 4 pin connector on the idle ECU when the car is running. That should bump the idle up between 2000 to 3000 RPM if the idle system is working. If you get no change than something...
  21. Replies
    41
    Views
    674

    [Engine] I never really found what effect the idle switch...

    I never really found what effect the idle switch has on the idle ECU. But with the idle switch off, you get ignition advance and that will most likely overcome the capability of the idle system to...
  22. Replies
    41
    Views
    674

    [Engine] The idle system still works without the idle...

    The idle system still works without the idle switch pressed. So like Elvis said, it's probably a frozen idle motor or bad idle ECU.
    If you unplug the 4 pin connector on the idle ECU the idle motor...
  23. Replies
    317
    Views
    38,445

    I've found a few companies send you a discount...

    I've found a few companies send you a discount code if you leave an item in your shipping cart. You really got a good deal. Think I paid about $250 for my same parts.
  24. Replies
    6
    Views
    246

    [Electrical] It would probably be a faulty gauge or bad...

    It would probably be a faulty gauge or bad connection on the gauge (flex circuit board). The volt gauge shares voltage with the temp gauge and the ground for the volt gauge is shared with the high...
  25. [Fuel] +1 You also need to have the mixture set to...

    +1

    You also need to have the mixture set to book values via dwell reading to have the WUR to work as designed. Also verify the WUR connector gets power and ground when the engine is running. ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4