FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    8,798
    Views
    1,917,961

    [General] Gotta' watch those sharp right turns!

    Gotta' watch those sharp right turns!
  2. [Engine] The leak and belt sounds like they unrelated to...

    The leak and belt sounds like they unrelated to the other problems.
    I agree WRT alignment and would check it closely before fixing the leak/pump.

    Does it start right up after it dies...without a...
  3. Thread: Lamda not working

    by Ron
    Replies
    18
    Views
    2,689

    [Fuel] Didn't re-read it all, so stabs in the dark:...

    Didn't re-read it all, so stabs in the dark:
    Ensure the three brass screws are shut.

    Perform all of the procedures (record, and post if off) at D:04:15/5.

    Record where the CO screw is...
  4. Thread: Hanging high idle

    by Ron
    Replies
    19
    Views
    440

    [Engine] IIRC, you can pull the FD and look down into the...

    IIRC, you can pull the FD and look down into the hole...you'll see what's going on.

    Be careful not to let the plunger fall out of the FD and hit anything...
  5. Replies
    10
    Views
    329

    [Engine] ..and the young man on the orange tractor wins by...

    ..and the young man on the orange tractor wins by a nose!
  6. Thread: Hanging high idle

    by Ron
    Replies
    19
    Views
    440

    [Engine] Just reread everything and have a few thoughts......

    Just reread everything and have a few thoughts...

    Pressing/pumping the throttle doesn't "give it gas to start" (no spray pump like a carb has).

    It cold, running rich with good idle, then high...
  7. Replies
    12
    Views
    417

    [Electrical] Sorry, no...It's the same in the Resources...

    Sorry, no...It's the same in the Resources section here. But you might try clicking the image to enlarge it, then again to enlarge again, then save it.
  8. Replies
    12
    Views
    417

    [Electrical] Best info I have, courtesy of post by Bill...

    Best info I have, courtesy of post by Bill Robertson. (See red square below.)
    67140
  9. Thread: Fuel pressure

    by Ron
    Replies
    11
    Views
    284

    [Fuel] ^^^ +1!

    ^^^
    +1!
  10. Thread: Car chugging

    by Ron
    Replies
    12
    Views
    336

    [Engine] Yeah, they have kept raising it over the years....

    Yeah, they have kept raising it over the years. The replacement regulators for rebuilders were mostly 14.2V regulators for decades (esp. GM)...we bought them by the 100s. But now, the ECU is in...
  11. Thread: Sound dyinosis

    by Ron
    Replies
    20
    Views
    535

    [General] Since it is RPM related, you might try switching...

    Since it is RPM related, you might try switching the engine off and and see what you hear while it is coasting.

    Also, you've made at least two OT political comments in this thread so far -- Three...
  12. Thread: Car chugging

    by Ron
    Replies
    12
    Views
    336

    [Engine] Specs on a stock alternators call for >13.5V. The...

    Specs on a stock alternators call for >13.5V. The regulators in most replacement alternators (modern) will settle at ~14.2V no matter how much the alternator "pushes"....just a matter of time.
  13. Thread: Sound dyinosis

    by Ron
    Replies
    20
    Views
    535

    [General] :yesss:

    :yesss:
  14. Thread: Sound dyinosis

    by Ron
    Replies
    20
    Views
    535

    [General] My guess is a loose screw.

    My guess is a loose screw.
  15. Thread: Car chugging

    by Ron
    Replies
    12
    Views
    336

    [Engine] Sounds like it could be the alternator (or...

    Sounds like it could be the alternator (or battery). But 40 minutes seems to be a little long unless you didn't use the lights, AC etc. Most auto parts stores will check them on the car for free. But...
  16. Thread: Hanging high idle

    by Ron
    Replies
    19
    Views
    440

    [Engine] I'm voting for the deceleration valve springs....

    I'm voting for the deceleration valve springs....
  17. Thread: Fuel pressure

    by Ron
    Replies
    11
    Views
    284

    [Fuel] Something seems wrong here -- The pressure at the...

    Something seems wrong here -- The pressure at the FD should match the pump pressure. (The accumulator, filter, and lines might restrict flow, but not pressure to the FD).

    Also, with 4.5 Bar at...
  18. Thank you for kindly confirming my suspicion(s).

    Thank you for kindly confirming my suspicion(s).
  19. Replies
    8
    Views
    1,773

    [Wanted] Since it's been years since the OP posted in this...

    Since it's been years since the OP posted in this thread and it looks like he had his fixed, I didn't want to close it if he is still looking.

    FWIW- You'll have better luck posting your own ad and...
  20. Replies
    8
    Views
    1,773

    [Wanted] Are you still looking for a "good one"?

    Are you still looking for a "good one"?
  21. LOL...so you haven't a clue why?? I drink...

    LOL...so you haven't a clue why??

    I drink mostly on special occasions -- "Probably" doesn't quite make it. :deviltail:
  22. ...that be the case, don't you owe MrChocky...

    ...that be the case, don't you owe MrChocky apology??
  23. [General] 67125

    67125
  24. [Heat & A/C] Another possible hiding place is at the front...

    Another possible hiding place is at the front shaft seal, behind the clutch assembly.
    A sniffer might save you a lot of work...
  25. [Fuel] If carb cleaner won't clean the screen up, use a...

    If carb cleaner won't clean the screen up, use a pick to remove them. A lot of people flush the line and leave them out since they are down stream from the filter. You can find fine mesh woven brass...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4