Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    15
    Views
    291

    [General] Great, thank you! I just placed my order. Cant...

    Great, thank you! I just placed my order. Cant wait to ditch the hex head bolts.
  2. Replies
    15
    Views
    291

    [General] Do you have a part number for this? I'm about to...

    Do you have a part number for this? I'm about to do my clutch and would love to change those bolts to something that won't rust immediately.
  3. Replies
    4
    Views
    300

    I ordered the gaskets from Rob, it will probably...

    I ordered the gaskets from Rob, it will probably be two weeks before I tackle the gasket replacement and the clutch at the same time.
  4. Replies
    3
    Views
    152

    [Electrical] http://dmctalk.org/showthread.php?16822-What%92s-t...

    http://dmctalk.org/showthread.php?16822-What%92s-this
  5. Replies
    4
    Views
    300

    [QUOTE=PJ Grady Inc.;238631] Will call to...

    Will call to discuss, need a pilot bearing from you as well.
  6. Replies
    16
    Views
    342

    [Heat & A/C] I'd still go by sight and not sound. If room...

    I'd still go by sight and not sound. If room allows, position your cellphone recording video at the cable end and move the switch to confirm. Even better is if you can remove the cable end and test...
  7. Replies
    16
    Views
    342

    [Heat & A/C] If you're asking about the temp knob I think it...

    If you're asking about the temp knob I think it would be difficult to tell if the cable is actually working without looking at the ends and making sure it's connected and moving - you won't hear the...
  8. Replies
    16
    Views
    342

    [Heat & A/C] The door that is controlled by the temp knob uses...

    The door that is controlled by the temp knob uses a cable. The rest are vacuum.
  9. Andrew is planning to go carb with his 3.0. As...

    Andrew is planning to go carb with his 3.0.

    As far as your trigger wire, if you use a shielded wire you'll have 0 problems.
    ...
  10. Best I can suggest absent any other advice is to...

    Best I can suggest absent any other advice is to take the gasket, set it on the block and see if there are any holes that need to be enlarged etc. If you get a block with some good 3.0 heads, let me...
  11. Replies
    16
    Views
    342

    [Heat & A/C] +1. Check the cable to the blend flap.

    +1. Check the cable to the blend flap.
  12. Replies
    10
    Views
    1,474

    [For Sale] Bump Still have the heads, camshafts (can be...

    Bump

    Still have the heads, camshafts (can be used on odd-fire but do not have distributor teeth), even-fire cranks, two intakes/fuel rails, timing covers, valve covers and probably other assorted...
  13. Replies
    4
    Views
    300

    Best Exhaust Manifold Gaskets?

    Title says it all, any thoughts on who sells the best? Experiences? Many many years ago I had purchased a few sets of then SpecialTAuto's stainless exhaust manifold gaskets. They blow out on me. I...
  14. Thread: Fuel pumps

    by dn010
    Replies
    5
    Views
    1,664

    Sorry for the delay, only seeing this now. Type...

    Sorry for the delay, only seeing this now. Type the below into the search box on ebay, this is what I have been using. Can't beat the $40 price right now but beware, this item has been on my watch...
  15. Replies
    18
    Views
    2,221

    It almost sounds like there was an issue with the...

    It almost sounds like there was an issue with the sale and the buyer wanted his money back but the seller already blew it.

    He relisted it down $1000 and threatens to part it out if it doesn't...
  16. Replies
    6
    Views
    257

    [Electrical] Is the harness the same on the driver side? I...

    Is the harness the same on the driver side? I keep popping the fuse when trying to move the driver mirror up or down but oddly it works fine in/out (passenger side is fine so I know it's not the...
  17. You posted before I could edit. You are right...

    You posted before I could edit. You are right correct. For some reason James told me that adjusting the pots in that fashion was incorrect for EDIS. Maybe I too need to clarify if something has...
  18. Deleted misinformation.

    Deleted misinformation.
  19. You can set timing offset, if needed, but it's...

    You can set timing offset, if needed, but it's not recommended with EDIS because if something happens to put you in limp home mode, the ECU will no longer be using the offset and if your sensor is...
  20. Also, the settings on page 65 are for a VR sensor...

    Also, the settings on page 65 are for a VR sensor connected directly to the MS, those settings are not appropriate for an EDIS setup. You need to use the settings that are on page 111, starting just...
  21. You can change the timing in MS, you just go into...

    You can change the timing in MS, you just go into ignition setting and select "fixed" timing and enter the timing value you want. Just remember it is fixed and won't change, if you rev up you can do...
  22. Well, updates?

    Well, updates?
  23. Thread: 3.0L engine swap

    by dn010
    Replies
    433
    Views
    56,799

    280! That is one bulletproof engine.

    280! That is one bulletproof engine.
  24. Replies
    18
    Views
    2,221

    Well, it's back... Still 90% complete after...

    Well, it's back...

    Still 90% complete after two years.

    https://www.ebay.com/itm/1981-DeLorean-2DR/183395301961
  25. Replies
    21
    Views
    3,887

    Green arrow goes towards the the shaft, you can...

    Green arrow goes towards the the shaft, you can see the splines are cut at an angle to make it easier to engage the splines on the shaft. Flat side up for the snap ring.

    I could be mistaken, but I...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4