FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. [Electrical] You lift the relay bank, pull one pin from the...

    You lift the relay bank, pull one pin from the fan relay socket, pull another pin from the fan fail socket and install that jumper in those blank pin locations. Look at the colors on you fan circuit...
  2. Replies
    63
    Views
    2,531

    [Frame & Body] For all those following this thread. Yes the...

    For all those following this thread. Yes the relays are installed for the actuators which is why they were working (almost).
  3. Replies
    63
    Views
    2,531

    [Frame & Body] Did you install the actuators? I only saw two...

    Did you install the actuators? I only saw two wires on your photos. Can you get a photo of your relay compartment. I still can't see how they work without the relays on an OEM door lock unit.
  4. Replies
    63
    Views
    2,531

    [Frame & Body] So it looks like Toby changed his lock actuators...

    So it looks like Toby changed his lock actuators to work with the OEM door lock unit. I have his old ones and it only had two wires where you had to reverse the ground and 12 volts to work them the...
  5. Replies
    46
    Views
    1,072

    [General] Some people run without it plugged in mostly to...

    Some people run without it plugged in mostly to stop idle hunting. If you do that you probably won't pass emission testing and expect less MPG.
  6. Replies
    46
    Views
    1,072

    [General] My guess is your O2 sensor is bad. It should go...

    My guess is your O2 sensor is bad. It should go closed loop in 2 to 3 minuets.
  7. Replies
    63
    Views
    2,531

    [Frame & Body] Maybe I'm wrong in thinking the OEM door lock...

    Maybe I'm wrong in thinking the OEM door lock unit was around 1 second of timing. I think my Zilla unit was around 100 ms. I now run my own design for the door lock unit.

    Since your running...
  8. Replies
    31
    Views
    874

    [Fuel] You jumper the large brown wire to the double...

    You jumper the large brown wire to the double yellow/red wires and that turns on the FV and lambda ECU. No need to turn on the key. You will hear the FV buzz. It takes about 60 seconds to dump a...
  9. Replies
    63
    Views
    2,531

    [Frame & Body] I found some caps. Timing now 340 ms. Not...

    I found some caps. Timing now 340 ms.

    Not sure if this is an OEM door lock unit and Hervey did some work on it so he put his sticker on the case.
  10. Replies
    63
    Views
    2,531

    [Frame & Body] I got the door lock unit today. The on time is...

    I got the door lock unit today. The on time is definitely short at 160 ms. for each lock and unlock. I think the OEM unit ran around 1 second. So Hervey put in relays with a high coil current...
  11. Replies
    31
    Views
    874

    [Fuel] You can jump the RPM relay connector to power up...

    You can jump the RPM relay connector to power up the FV and lambda but I just use that to remove the rest pressure before I need to pull a fuel hose.
  12. Replies
    86
    Views
    7,345

    [Electrical] I got the same box you show also made in Romania....

    I got the same box you show also made in Romania. I think my 4 sided LEDs will never work for automotive lighting.
  13. Replies
    31
    Views
    874

    [Fuel] 11.5 volts on the fuel pump should work but if...

    11.5 volts on the fuel pump should work but if your dropping 2.5 volts somewhere you should find out where and fix it. Connectors, bad connections, RPM relay.

    Limited engine RPM could be fuel or...
  14. Replies
    86
    Views
    7,345

    [Electrical] I got one of those Canada Hella housing and...

    I got one of those Canada Hella housing and tested it with my 4 sided LEDs and it still looks like a spot light. I don't have an extra "cheap" housing or I would set up something to give a better...
  15. Replies
    8,284
    Views
    1,444,889

    [General] Email me for current prices. I like to verify I...

    Email me for current prices. I like to verify I have the items ready before you order. I try to keep everything stocked but there are times when I get flooded with sales one week and then nothing...
  16. Replies
    46
    Views
    1,072

    [General] Yes the O2 sensor responds to mixture changes...

    Yes the O2 sensor responds to mixture changes very fast. The narrow band sensor just looks for any oxygen or not. So the lambda ECU is making the mixture richer if that O2 sensor voltage is above...
  17. Replies
    46
    Views
    1,072

    [General] I don't think timing or valve adjustment would...

    I don't think timing or valve adjustment would stop the ability to adjust dwell.
  18. Replies
    46
    Views
    1,072

    [General] That is swinging to much if your seeing it swing...

    That is swinging to much if your seeing it swing 45 to 20 up and down. It should be half that or less. Have you replaced the O2 sensor? A very small adjustment normally makes a large dwell change. ...
  19. Replies
    46
    Views
    1,072

    [General] Removing or plugging the adjustment hole will...

    Removing or plugging the adjustment hole will make a small change to the idling engine but the working idle system should quickly compensate. That is if everything is adjusted properly. Your...
  20. Replies
    8,284
    Views
    1,444,889

    [General] Some day I will have to do a circuit board to LED...

    Some day I will have to do a circuit board to LED light the cigar lighter. I did do a one off board on mine a long time ago which used 6 LEDs.
  21. Replies
    8,284
    Views
    1,444,889

    [General] I drove the D today to the post office. I don't...

    I drove the D today to the post office. I don't drive it much since I retired since I would take it once a week to work. But two things have changed. First is it seems to go into reverse every...
  22. Replies
    86
    Views
    7,345

    [Electrical] I bought a pair of 4 sided LEDs and they did not...

    I bought a pair of 4 sided LEDs and they did not give me anything near a normal pattern. It was more like a spot light but that was with that cheaper housing. I do plan to test those 4 sided ones...
  23. Replies
    24
    Views
    1,207

    It may work with one pulse on the distributor so...

    It may work with one pulse on the distributor so you get a reference of which stroke your on for #1 cylinder but it's going to take some fancy software to keep track of when all cylinders need to...
  24. Replies
    86
    Views
    7,345

    [Electrical] Now that is good info. I did some pattern...

    Now that is good info. I did some pattern testing when I installed LEDs into the cheap housings and never was very happy with the pattern. But I was comparing it to my 2018 Camry which has really...
  25. Replies
    63
    Views
    2,531

    [Frame & Body] Remember your lock ECU may have to short of an on...

    Remember your lock ECU may have to short of an on time for actuators. I never tested the timing, just the function when I had it here. The stock lock ECU had plenty of time to work actuators but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4