Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds; generated 4 minute(s) ago.

  1. Replies
    7
    Views
    102

    [Electrical] If your blower breaker has 4 wires on it you...

    If your blower breaker has 4 wires on it you probably have the mod.

    Your VIN is late enough that it should have been modified.
  2. Replies
    7
    Views
    128

    Looks like only 4 of the 18 fuses go to battery...

    Looks like only 4 of the 18 fuses go to battery power. Four go to one AUX relay. Three go to the other AUX relay. The rest have non battery connections to both sides of the fuse. So your looking...
  3. Replies
    7
    Views
    102

    [Electrical] If you have the starter relay mod installed. ...

    If you have the starter relay mod installed. Just pull that relay and jumper the two terminals (row of three, the ends).
  4. Replies
    7
    Views
    128

    Depends where you mount it if all the existing...

    Depends where you mount it if all the existing wires would be long enough. Then you need to make your own wire list to document what you did.
  5. Replies
    7
    Views
    128

    Unless it comes with a complete harness, you...

    Unless it comes with a complete harness, you still need to make all the connections.
  6. [Engine] You would need to make that wiring change to use...

    You would need to make that wiring change to use a standard relay or my relay.

    I also use my relays for replacing the AUX relays but had to put new pins on the wires since the OEM relays used...
  7. [Engine] Yes the lambda relay normally runs very hot. You...

    Yes the lambda relay normally runs very hot. You can put in a standard relay if you rewire that center pin.

    Remove the center pin with the red/purple wire.
    Cut the pin off and connect that...
  8. Replies
    16
    Views
    354

    [General] 1 90128A292 Zinc-Plated Alloy Steel Socket Head...

    1 90128A292 Zinc-Plated Alloy Steel Socket Head Screw, M10 x
    1.5 mm Thread, 60 mm Long, Packs of 10
    3
    Packs
    3 0 8.30
    Per Pack
    24.90
    2 94241A560 316 Stainless Steel Split Lock Washer for M10...
  9. Replies
    7,497
    Views
    1,094,826

    [General] I think I could pull it enough to crimp on butt...

    I think I could pull it enough to crimp on butt spices and then solder.
  10. Replies
    7,497
    Views
    1,094,826

    [General] Probably that two pin connector for the fuel...

    Probably that two pin connector for the fuel pump. I just removed the connector since you can undo the wires at the pump, you really don't need a connector.
  11. Replies
    4
    Views
    118

    [Electrical] Probably a wire has shorted onto another wire. I...

    Probably a wire has shorted onto another wire. I would start by pulling the blue bulkhead connector off (I think your car should start with it off). That would confirm or eliminate the wires in the...
  12. Replies
    16
    Views
    354

    [General] Hardware store washers are not marked. I wonder...

    Hardware store washers are not marked. I wonder what grade washers were used in production.

    If you used SS bolts maybe that was the problem.
  13. Replies
    16
    Views
    354

    [General] I have seen a few times when I open my garage...

    I have seen a few times when I open my garage door everything inside get wet from condensation. Those cold nights and humid summer days are the killers.
  14. Replies
    16
    Views
    354

    [General] I'm seeing carbon steel hardness of Rockwell B of...

    I'm seeing carbon steel hardness of Rockwell B of 71 and 316 stainless of Rockwell B of 79. I also know stainless is a little harder to machine. I would like to know if your washers did cause the...
  15. Replies
    16
    Views
    354

    [General] Black oxide bolts

    I had replaced my axle bolts with Allen cap black oxide bolts. But with less than 100 miles the heads of those bolts are completely rusted. So I found zinc bolts at MaterCarr. I also mostly use...
  16. [Fuel] +1 I've found my car starts faster in the summer...

    +1
    I've found my car starts faster in the summer when the CSV is not firing (if car has not sat for many days). I do need the CSV if the car sits for a week or longer to get it started.

    But the...
  17. Replies
    7,497
    Views
    1,094,826

    [General] Here is another thread option. ...

    Here is another thread option.

    http://dmctalk.org/showthread.php?3188-Door-switch-alternatives&highlight=mercury
  18. Replies
    7,497
    Views
    1,094,826

    [General] I Helicoil'ed my three starter mounting bolts...

    I Helicoil'ed my three starter mounting bolts today. I'm don't trust China tools much but for this job this kit worked fine. Not much of a test since it's not in a steel repair. I used blue...
  19. [Electrical] That removed relay with the jumper is to make the...

    That removed relay with the jumper is to make the AC panel lights only come on when the car lights are on.

    Looks like your fuse #7 has seen overheating.

    One of your circuit breakers is not...
  20. Replies
    10
    Views
    349

    A screw extractor is really only good if you...

    A screw extractor is really only good if you broke the bolt when you over tightened it. Never seems to work with a corroded bolt that broke trying to remove it.
  21. [Engine] A lot of cars the fans turn on around the 1/4...

    A lot of cars the fans turn on around the 1/4 mark and some cars don't turn on till the 220 mark. Don't know why that difference. But the fans should turn on after the thermostat opens and the...
  22. Replies
    4
    Views
    255

    It should not matter as long as the o-ring on the...

    It should not matter as long as the o-ring on the orifice tube is sealing inside the pipe. So I would not force it to far and just put the accumulator back on over it.
  23. Replies
    21
    Views
    3,894

    Thanks for that suggestion. I put the boots on...

    Thanks for that suggestion.

    I put the boots on the axle. Remember when you install the large clamp, place the clamp where you want it to sit and put the clamping bump between two bolt holes so...
  24. Replies
    21
    Views
    3,894

    Ready to assemble. Note the CV housing has a...

    Ready to assemble.

    Note the CV housing has a ring on one side. I don't think it matters if you flip it but on my car the side with ring is on the side without the boot. I've seen a few you tube...
  25. Replies
    21
    Views
    3,894

    I think your all correct. I tried sliding it on...

    I think your all correct. I tried sliding it on the shaft both ways and it looks like I could only get the C clip on when the green dot (cut spline) side is put onto the shaft first.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4