FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Josh

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. [For Sale] x2. To further the issue of mis-adjustment, If...

    x2.

    To further the issue of mis-adjustment, If someone were to over adjust this contraption it could cause the pressure plate to not fully engage. This can result in damage to the release bearing,...
  2. Replies
    14
    Views
    655

    The timing is kind of poor, there is already a...

    The timing is kind of poor, there is already a very polished sequential taillight board available through DMCNW.
    ...
  3. Thread: Coolant

    by Josh
    Replies
    18
    Views
    706

    [General] vaccum fill is the best way to fill the coolant...

    vaccum fill is the best way to fill the coolant system in a delorean. If you are doing it any other way you are making things difficult for yourself.
  4. Replies
    5
    Views
    318

    [Transmission 5-Speed] Im no expert but it looks like you need new axle...

    Im no expert but it looks like you need new axle flange seals and a rear main seal for the engine. Both are common failure seals.
    David, If you call this a minor leak I am scared to see what a...
  5. Replies
    14
    Views
    737

    Amazing work, looks very well suited to the car.

    Amazing work, looks very well suited to the car.
  6. Replies
    5
    Views
    327

    Tonight I used a spare output from the ecu to...

    Tonight I used a spare output from the ecu to turn the power steering off over a certain speed, and back on at another. This is a major improvement for the highway. Still, the delay is a second or...
  7. Replies
    5
    Views
    327

    Nothing special about it. Most of the Electric...

    Nothing special about it. Most of the Electric Power Steering (EPS) setups are similar. I pulled out of what car was available and it happened to be a nissan versa. A Yaris unit would be ideal as it...
  8. Replies
    5
    Views
    327

    DIY Power steering

    I didn't want to spend $3000 cdn on a power steering column so I made one myself.

    Used a motor from a Nissan Versa. Junk yard charged me $80 for it. Took about 8 hours to fabricate everything. Ran...
  9. Replies
    7
    Views
    452

    It looks like you are using microphone shields as...

    It looks like you are using microphone shields as air filters? What happens when it rains, or you drive somewhere dusty. I never understood velocity stacks on a car driven with any regularity.
  10. Replies
    3
    Views
    788

    [Frame & Body] I ended up just kind of putting them on by feel....

    I ended up just kind of putting them on by feel. LOL. Make it up as you go along.
  11. Replies
    28
    Views
    1,512

    [General] I would love to do a TDI swap, I have been saying...

    I would love to do a TDI swap, I have been saying this for several years.

    Not in my own car though...
  12. Replies
    17
    Views
    694

    Ive made two posts on the subject. "over and...

    Ive made two posts on the subject. "over and over". No
  13. Replies
    17
    Views
    694

    this again. Just buy Dave's flasher units.

    this again. Just buy Dave's flasher units.
  14. Replies
    101
    Views
    14,772

    I enjoy that you have used the word clunky...

    I enjoy that you have used the word clunky several times since my last post.
  15. Replies
    101
    Views
    14,772

    Using two relays to run a side marker is pretty...

    Using two relays to run a side marker is pretty terrible circuit design and clunky.
    If you are using incandecents having flashing side markers is as easy as wiring the lights in series.
    With LEDs...
  16. Thread: Momo Wheel

    by Josh
    Replies
    7
    Views
    585

    Some quick reading shows the bolt pattern for the...

    Some quick reading shows the bolt pattern for the wheel is different and the turn signal pins are not present
  17. Thread: Momo Wheel

    by Josh
    Replies
    7
    Views
    585

    I could get them made if someone provided me with...

    I could get them made if someone provided me with some sort of sample or dimensions.
  18. Replies
    15
    Views
    1,713

    [General] I have a set of these on my car, put about...

    I have a set of these on my car, put about 10,000kms on just this summer with them. They work great.

    Quality product and they look great. Get lots of compliments about them.
    ...
  19. Replies
    34
    Views
    4,807

    [Electrical] Im getting old, I dont seem to enjoy a loud...

    Im getting old, I dont seem to enjoy a loud exhaust anymore lol.
    I think I lost about 10whp installing cats but it is worth it.
  20. Replies
    34
    Views
    4,807

    [Electrical] I cannot hear the low speed over the engine, I...

    I cannot hear the low speed over the engine, I can hear the high speed over the engine if i am standing outside the car (at idle). Inside the car with the engine running I cannot hear them at all....
  21. Replies
    6
    Views
    336

    [Transmission Auto] hear hear. I also have a vss pickup for the...

    hear hear.

    I also have a vss pickup for the UN1 now.
    https://i.imgur.com/PgC6YUdh.jpg
  22. Replies
    34
    Views
    4,807

    [Electrical] I really like the Multispeed fans for my setup,...

    I really like the Multispeed fans for my setup, but for a stock delorean the one speed fan would be the best.
    I think the ones I have xref to a MK3 golf (and similar)
  23. Replies
    34
    Views
    4,807

    [Electrical] Following up These VW fans are the highest...

    Following up

    These VW fans are the highest performance fans you can fit to your delorean than I know of.
    I just got back from a 6100km road trip with AC blasting the entire time, up to 100F...
  24. Replies
    27
    Views
    9,864

    I had to lube it up quite alot before it would...

    I had to lube it up quite alot before it would pop in. Very snug but it works.
  25. Replies
    6
    Views
    5,046

    I did a bake/flame off then a light sand blasting...

    I did a bake/flame off then a light sand blasting to clean it up afterwards.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4