FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14
    Views
    393

    [General] You may want to consider doing both it you do one...

    You may want to consider doing both it you do one so theyíre not mismatched after itís all done.
  2. Replies
    14
    Views
    393

    [General] Tough decision you'll have to make. We can't see...

    Tough decision you'll have to make. We can't see what you're working with nor are we getting the bill for the work. I will say that if you don't like it, change it.
  3. [Suspension] When I had noise issues over any little bump in...

    When I had noise issues over any little bump in the road, my lower control arm bushing was shot - the rubber was pretty much all pressed out of the bushing and this allowed everything to move around....
  4. Replies
    14
    Views
    393

    [General] I have gotten away with polishing up the black...

    I have gotten away with polishing up the black portions since I've had my car but it is time for me to refresh them completely. Here is the thread I started with info on what black to use:
    ...
  5. [Suspension] Here is my guess - what is the condition of your...

    Here is my guess - what is the condition of your lower control arm bushings?
  6. [General] Find out whose stainless arms you have and...

    Find out whose stainless arms you have and contact them for input on changing the bushings (I'm not aware of anyone other than DPI selling stainless ones so you might start there). From what I...
  7. Replies
    13
    Views
    599

    [Frame & Body] It might be better to use a block of wood so that...

    It might be better to use a block of wood so that it can absorb some of the strike should the bar/bracket release on you while you're adjusting it.
  8. [General] You donít need to worry about the spring, the...

    You donít need to worry about the spring, the shock is there holding everything together.
  9. [General] I can't remember if I've replaced the upper...

    I can't remember if I've replaced the upper bushings or not on mine, instead it is always the lower ones that have gone bad. You could take it apart an try it with a bushing tool but personally I'd...
  10. [General] The UPPER control arms don't need the springs to...

    The UPPER control arms don't need the springs to be removed in order to remove the arm.

    You can A- lift the car up and remove the upper arm or B- rest the weight of the car on a jack or block etc....
  11. Replies
    18
    Views
    576

    [Engine] If all else fails, you can try soaking the 2.8L...

    If all else fails, you can try soaking the 2.8L cap in gas or solvent to try to clean up the internals and see if it works any better than it did. Unfortunately I only have the B280F 'separator'...
  12. Replies
    51
    Views
    1,746

    [Suspension] The difference I could tell between early/late...

    The difference I could tell between early/late frames was that they riveted the plate on the underside of the engine cradle on early frames where the lower links are located (I can try to take a...
  13. Replies
    159
    Views
    43,369

    The cups would make shifting difficult on the...

    The cups would make shifting difficult on the 5-speed.
  14. Thread: EFI VS Stage II

    by dn010
    Replies
    45
    Views
    2,048

    [General] You guys have obviously forgotten about the last...

    You guys have obviously forgotten about the last time this topic came up. It's all about the buttmeter!
  15. Replies
    13
    Views
    599

    [Frame & Body] Those PDFs are good but don't tell you to remove...

    Those PDFs are good but don't tell you to remove the strut and open the door as far as possible. It's important because the further you can get the door open, the less torsion energy the bar will...
  16. Replies
    13
    Views
    599

    [Frame & Body] I don't think you need to re-measure it, you can...

    I don't think you need to re-measure it, you can tell just by the pic that it is adjusted way too much.
    So your options now are A-find someone with a jig to help you adjust the bar or
    B you can...
  17. Replies
    13
    Views
    599

    [Frame & Body] Your measurement should come from the bottom of...

    Your measurement should come from the bottom of the door to the sill, looks like way too much.
  18. Replies
    13
    Views
    599

    [Frame & Body] You can remove the door struts, let the doors...

    You can remove the door struts, let the doors hang open with the torsion bar energy and see how much they are open. If my memory is fine, it should be about 2-4". If it is more or less then the bar...
  19. Replies
    1
    Views
    235

    Remote controlled D

    I didn't see this posted after a brief search, but for those who are interested:

    https://www.thesun.co.uk/motors/9680655/inventor-builds-remote-controlled-back-to-the-future-delorean/
  20. Replies
    8
    Views
    482

    [Wanted] Sorry Steve, canít seem to locate mine.

    Sorry Steve, canít seem to locate mine.
  21. Replies
    84
    Views
    7,560

    [General] What coil are you running?

    What coil are you running?
  22. Replies
    8
    Views
    482

    [Wanted] I may have one as well, will check this evening.

    I may have one as well, will check this evening.
  23. Replies
    12
    Views
    611

    [General] I don't buy it. Your beloved tech manual says...

    I don't buy it. Your beloved tech manual says nothing about retightening clamps and I checked both volumes.
  24. [General] Open the door and pry up at the ends. You will...

    Open the door and pry up at the ends. You will still probably rip a few fir trees out, the cardboard material is crap.
  25. [For Sale] Would you be willing to sell the dust cover...

    Would you be willing to sell the dust cover separately?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4