Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.50 seconds.

  1. Replies
    3
    Views
    122

    [General] I have the EU radiator and Toby fans which I like...

    I have the EU radiator and Toby fans which I like very much. There are some new vendors products I have not seen in person yet.
  2. [Electrical] Did it always do that? I had an old used car...

    Did it always do that? I had an old used car that would do the same thing. That turned out the PO put a wire to turn the fans all the time (engine running) but that also feed power back to the...
  3. [Engine] Most RPM meters use the ignition coil (negative...

    Most RPM meters use the ignition coil (negative side). There are some optical RPM meters but you usually need to add a foil reflector on the pulley.
  4. Replies
    7
    Views
    276

    [Fuel] If your boots are original, you probably need to...

    If your boots are original, you probably need to cut them off the injectors. The rubber gets so hard you can't pull them off.
  5. [Fuel] If your fuel lines were leaking, that would cause...

    If your fuel lines were leaking, that would cause a hot start problem.
  6. Replies
    7
    Views
    276

    [Fuel] You may want to get new rubber seals also. New...

    You may want to get new rubber seals also. New ones will hold injector tighter.
  7. Replies
    8
    Views
    266

    [Electrical] The two switch wires should be green/purple. Some...

    The two switch wires should be green/purple. Some cars have a glass fuse in the harness by the brake switch.
  8. [Electrical] Do you have any alarm system? Keep pulling all...

    Do you have any alarm system? Keep pulling all the fuses until you see the light go away.
  9. Replies
    18
    Views
    617

    [Fuel] My own design.

    My own design.
  10. Replies
    18
    Views
    617

    [Fuel] The old pump that buzzed was a DMCH part. It was...

    The old pump that buzzed was a DMCH part. It was what they found to replace the NOS pumps.

    There new pump is different and includes the fuel level sender.
  11. Replies
    18
    Views
    617

    [Fuel] I had the fuel pump buzzing after the gas got hot...

    I had the fuel pump buzzing after the gas got hot and I had the spring installed and Hervey's hot air dam. It was only after I installed a fuel cooler it stopped. That was before DMCH offered the...
  12. Thread: Stalls

    by Bitsyncmaster
    Replies
    8
    Views
    401

    My guess is your mixture is not set correct. Use...

    My guess is your mixture is not set correct. Use a dwell meter to set it.
  13. No it's not a fault of the RPM relay. If you...

    No it's not a fault of the RPM relay. If you find the engine stalls letting off the throttle, most times you can solve that problem turning the curb idle screw up (clockwise) a little.
  14. Replies
    4
    Views
    388

    The reason to use brass nuts is so they don't...

    The reason to use brass nuts is so they don't "gall" into stainless studs.

    Yes normal steel is stronger than stainless but you don't have to torque the nuts that much.
  15. Replies
    3
    Views
    368

    My clutch went out without any warning. I guess...

    My clutch went out without any warning. I guess after the 1 hour drive that day just triggered the failure. It would suddenly slip when cruising. I could stop and most of the time get another few...
  16. Replies
    1
    Views
    140

    [Electrical] That looks good for the stock idle motor. I...

    That looks good for the stock idle motor.

    I get these values but mine include some wiring from the idle motor to the ohm meter.

    10.7
    11.8
    22.0

    You always get a little different readings...
  17. Replies
    7
    Views
    432

    [General] My valley looked smooth when I cleaned it. If...

    My valley looked smooth when I cleaned it. If yours is not leaking yet, I would coat it with something. I used rust-oleum paint and just brushed it on.
  18. Replies
    17
    Views
    476

    [Heat & A/C] +1 But since your idle is only 650 RPM that...

    +1

    But since your idle is only 650 RPM that could account for lower high side pressure at idle.
  19. [Electrical] It looks like you need to attach a magnet to a...

    It looks like you need to attach a magnet to a rotating shaft and then mount a sensor near it to measure RPM.
  20. [Engine] I would not think your 200 watt fans would affect...

    I would not think your 200 watt fans would affect my idle ECU even if the voltage to the ECU dips quite low.

    Have you noticed any other problems since you installed those fans?
  21. [Engine] I have seen one fuel filter in the D completely...

    I have seen one fuel filter in the D completely blocked. Measured 0 PSI at the FD with the pump running.
  22. [Engine] I've never pulled an advance solenoid apart. All...

    I've never pulled an advance solenoid apart. All I know is when not powered, the advance is on and the vent is closed. When powered the advance is off and vent is open. I did find one solenoid...
  23. [Engine] We just had another owner have a problem with...

    We just had another owner have a problem with advance coming on at idle. It would come and go. After 3 idle ECUs and a new vacuum solenoid it still was intermittent. It has to be an intermittent...
  24. Does your voltage drop when you run the AC? Do...

    Does your voltage drop when you run the AC? Do you still run stock ignition?
  25. [Engine] At least you can bump your idle up with the curb...

    At least you can bump your idle up with the curb idle screw to get home. PM me your address and I will send you another ECU and you can return the old ECU in the same box. Let me know if you have...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4