FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    143
    Views
    16,779

    After printing 5 test prints flat (cut to the...

    After printing 5 test prints flat (cut to the left side 5.2 inches), I printed one full size face plate. I had to position the part at a 51 deg angle to get it to fit. My printer can do much higher...
  2. Replies
    8
    Views
    117

    [Transmission 5-Speed] Does the car stop moving up the hill? Not...

    Does the car stop moving up the hill? Not counting momentum.
  3. Replies
    143
    Views
    16,779

    Thanks. I have been looking at the many...

    Thanks. I have been looking at the many available printers. I see some have heated plates, heated enclosures, flex plates, and a lot of new stuff I have to read up on.

    I was wondering if two...
  4. Replies
    143
    Views
    16,779

    I'm working on printing an HVAC faceplate with...

    I'm working on printing an HVAC faceplate with improved less light bleeding shields. My Formlabs printer can only print flat to 5.4" and I wanted to print flat so the back side has no supports. I...
  5. [Fuel] The RPM relay turns the lambda system on by...

    The RPM relay turns the lambda system on by powering the "main fuel relay" (lambda relay). First is make sure that lambda relay is the correct type. If you have no FV buzz still then you need to...
  6. Replies
    29
    Views
    1,056

    [Transmission 5-Speed] I think he was drilling out a stuck bolt and went...

    I think he was drilling out a stuck bolt and went to deep.
  7. Replies
    45
    Views
    3,016

    [General] Thanks for the photo. Now it came back to me...

    Thanks for the photo. Now it came back to me from 10 or more years ago when I built my first door lock unit. I had the Zilla case which has a circuit breaker mounted inside of it. So I decided to...
  8. Replies
    45
    Views
    3,016

    [General] Can someone post a photo of the wire end of there...

    Can someone post a photo of the wire end of there harness connector for the door lock unit. Not sure if mine was stock with a large brown wire in the top single pin on the connector. I had the...
  9. [General] There are some engines in other cars where they...

    There are some engines in other cars where they said to put a sealer on some bolts because they went into the water jacket. I would defiantly try a good sealer on the bolt. Make sure the bolt is...
  10. Replies
    7
    Views
    272

    [Engine] That looks more like 0.010" or more but as long...

    That looks more like 0.010" or more but as long as both surfaces are parallel it should not be a problem.
  11. Replies
    45
    Views
    3,016

    [General] Thanks. I contacted them.

    Thanks. I contacted them.
  12. Replies
    5
    Views
    244

    [Fuel] You will hear some noise from the primary...

    You will hear some noise from the primary pressure regulator. Not sure if that noise is always there when engine is running but I hear it if the pump is running without the engine.
  13. Replies
    45
    Views
    3,016

    [General] Toby has no stock of his fans with connector. He...

    Toby has no stock of his fans with connector. He does have them without connector. That is the two pin connector. I have a blue idle ECU connector that came with an idle ECU core I bought. I guess...
  14. Replies
    45
    Views
    3,016

    [General] I had a customer that wanted to use a remote. So...

    I had a customer that wanted to use a remote. So his system seems to use a negative pulse to lock or unlock. So as I was changing the software, I found a bug with the remote operation that I had to...
  15. Replies
    45
    Views
    3,016

    [General] It's mostly the pins that would require quite an...

    It's mostly the pins that would require quite an investment to produce. Actually making little changes to pin design would enable the female pins to be removed easily. The AMP connectors are much...
  16. [Electrical] When you go to key position 2 your adding more...

    When you go to key position 2 your adding more load so a bad connection could make that feed through go open and kill everything. If it's not the feed though connections then you will need to...
  17. [Electrical] If your battery is good the first thing to check...

    If your battery is good the first thing to check are the two feed through bolts and nuts behind the rear deck board. You have to remove the vertical board by removing the hooks on top which hold the...
  18. [Electrical] I had one side blow fuses and it turned out a...

    I had one side blow fuses and it turned out a screw in the center console shorted a wire on the right side. Try pulling the two screws on the shifter plate and see if your problem goes away.
  19. [For Sale] I was just asking because I had a mug my daughter...

    I was just asking because I had a mug my daughter got me with my grand kids photos on it and a short time later the photos scratched off.
  20. [For Sale] It says hand wash so the Vin print is not done...

    It says hand wash so the Vin print is not done before the mug is glazed? Or is it?
  21. Replies
    45
    Views
    3,016

    [General] The two inputs are the two empty solder pads...

    The two inputs are the two empty solder pads labeled W10 and W11. Right now I have software looking for a rising edge to do a lock or unlock. W10 is for lock and W11 is for unlock. Voltage from...
  22. Replies
    45
    Views
    3,016

    [General] Ive got 8 units (no connector) with 9 inch long...

    Ive got 8 units (no connector) with 9 inch long wires ready to sell. If you wanted one I will sell for $75 including shipping to US address.

    I attached my notes I started for documentation. Also...
  23. Replies
    17
    Views
    1,175

    [General] Well I've decided the LEDs I got on my last order...

    Well I've decided the LEDs I got on my last order are the best ones yet. The red color is good and orange are good for the amber lights. I went ahead and ordered circuit boards. The boards ended...
  24. Replies
    45
    Views
    3,016

    [General] Britishwiring is only showing 16 of the 9 pin...

    Britishwiring is only showing 16 of the 9 pin pairs in stock. I wonder if they can get more. I do have some 9 pin connectors but I would need a supply of them to sell many units with the connector...
  25. Replies
    45
    Views
    3,016

    [General] I did some more thought on noise. I could see if...

    I did some more thought on noise. I could see if the car was moving or on a bad road the ground connections on the door switches could be noisy. So my software remembers what condition the locks...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4