FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    95
    Views
    5,105

    If the schematics are the same they will work as...

    If the schematics are the same they will work as long as the Amp rate is high enough. The numbers can tell you that, along with mounting, etc. Dipped Beam, Main Beam, Fan 3rd Speed, Fan 4th Speed,...
  2. Replies
    95
    Views
    5,105

    The 0332209150 relay will work for most of the...

    The 0332209150 relay will work for most of the others.
    Look on the side of it for a schematic. They will match.
    I've seen several used for the ignition resistor by-pass...
  3. Replies
    95
    Views
    5,105

    Damit, you were supposed to find that the BLG...

    Damit, you were supposed to find that the BLG wire had no power first.:)

    Good job!
  4. Replies
    95
    Views
    5,105

    If it was warm, I would check the LG wire at the...

    If it was warm, I would check the LG wire at the pin 6 (33 in chart) of the 7 pin White bulkhead connector. Otherwise, it is probably OK since the thermal throttle enrichment switch could be...
  5. Replies
    95
    Views
    5,105

    $ .03 Just check the voltages at the...

    $ .03

    Just check the voltages at the components. If they are OK you are wasting your time checking the rest (except for intermittent problems...or preventive maintenance). Use an ice pick tester...
  6. Replies
    95
    Views
    5,105

    $.02 Rich, I think you meant 500 to 700, not...

    $.02

    Rich, I think you meant 500 to 700, not 5000 to 7000.

    If you are sure there are no vacuum leaks, check out the 3 switches (see below).
    If no luck, I'd put a CIS fuel pressure gauge on it...
  7. Replies
    8,132
    Views
    1,349,091

    [General] :thumbup::thumbup::thumbup:

    :thumbup::thumbup::thumbup:
  8. Thread: PRV engine

    by Ron
    Replies
    4
    Views
    536

    [Wanted] Missing Post(s)? Please review the Sticky...

    Missing Post(s)?

    Please review the Sticky titled "***-SECTION-RULES-***-Please-READ-BEFORE-POSTING-***".
  9. [Fuel] The WR wire should have 12V on it while cranking,...

    The WR wire should have 12V on it while cranking, only.
    If you follow the steps in my previous post, in order, any problem with the CSV or the wiring for it should be identified.
  10. Replies
    17
    Views
    2,837

    [Fuel] I only mentioned it because you said, "If it...

    I only mentioned it because you said, "If it won't fire, no reason to worry about anything else yet."
    People roaming the junk yards looking for an engine use it all the time -- Helps identify if...
  11. Replies
    17
    Views
    2,837

    [Fuel] $.02 If you want to fire it up, disconnect the...

    $.02

    If you want to fire it up, disconnect the fuel pump and use starting fluid....

    Gummy deposits or a blockage in the lines indicates that you should remove the lines and clean them one at a...
  12. [Fuel] That sounds normal. Unplug the TTS. At the Hot...

    That sounds normal.

    Unplug the TTS. At the Hot Start Relay, jumper the UB wire to the B (ground) wire. If it still starts right up COLD, the TTS or its wiring is bad. Check the TTS socket-plug, WR...
  13. [Fuel] Yes, that sounds very close to ideal for stock...

    Yes, that sounds very close to ideal for stock DutyCycle (pulsating, centered at 44.44%, hot).

    Seems to be some confusion... Are/were you having starting problems hot and cold?

    Your temp,...
  14. [Fuel] This is the one AutoZone says will fit....

    This is the one AutoZone says will fit.

    It basically has no affect on the engine while cold or during starting because the sensor must see 572F (300C) minimum...

    FWIW, steady 50% duty cycle...
  15. Replies
    13
    Views
    528

    [Fuel] Maybe you can see the wires clear enough here:...

    Maybe you can see the wires clear enough here:
    62253
    Click>Click again in new>Save...
  16. Replies
    14
    Views
    773

    [General] :thumbup:

    :thumbup:
  17. Replies
    12
    Views
    796

    [Engine] LoL @ earlier :TrainWreck: Depending on...

    LoL @ earlier :TrainWreck:


    Depending on which oil sender may be leaking, maybe put the oil pressure gauge in the idiot light port instead and confirm the dash gauge in the process. Kill 4...
  18. Replies
    14
    Views
    4,641

    [Wanted] Your best bet is to post your own Wanted Ad....

    Your best bet is to post your own Wanted Ad.
    (Looks like this one should have been closed a long time ago.)
  19. Replies
    4
    Views
    664

    +1 About has to be, if all speeds work in any...

    +1

    About has to be, if all speeds work in any mode, because of the way it's wired.


    It can be done. Small hands will help...and a long forearm.
    Aligning it all up while starting the small...
  20. Replies
    14
    Views
    897

    [Electrical] +1 Dave. The only other reason I can think of is...

    +1 Dave.
    The only other reason I can think of is so you know that you you caused a new problem during installation...

    The door light fuse (#12) should always be hot (12V+ both sides) regardless...
  21. [Engine] No (it would probably die), I was thinking just...

    No (it would probably die), I was thinking just turn the key to Run for a quick comparison/elimination...

    +1 Dave and Rich, except it's pins 5, 8, 9.
  22. Now I'm confused. When I asked if you were...

    Now I'm confused. When I asked if you were re-setting the tensioner(s) the same way, you sad no and that they just pop back and lock on a tooth. Which I thought meant you were not resetting the screw...
  23. Replies
    4
    Views
    804

    [For Sale] Missing Posts? Please review the Sticky...

    Missing Posts?

    Please review the Sticky titled:
    PLEASE-READ-BEFORE-POSTING-!!!-For-sale-Wanted-section-Rules.
    RE:
    For Sale- Do not post a question or remark if you do not intend to buy the...
  24. Replies
    4
    Views
    390

    [Engine] Double check that the washers/spacers for the...

    Double check that the washers/spacers for the bearings are stacked correctly.
  25. [Engine] You might try watching the valve while pressing...

    You might try watching the valve while pressing and releasing the plug to see if that changes its position...
    Or comparing the pressed and released RPM with the unplugged RPM.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4