FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DARCOM

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    794

    I have always had a similar issue. But i have...

    I have always had a similar issue. But i have megasquirt set at 900 rpm so it adjusts automatically to target that rpm in msextra.
  2. Replies
    61
    Views
    4,775

    I have had mine for 26 years.

    I have had mine for 26 years.
  3. Replies
    15
    Views
    1,109

    [General] Yes all my cars. The lift is rated at 6000...

    Yes all my cars. The lift is rated at 6000 pounds. The image I posted is the lift at max height. I also use stablelize bars on the front and back when under the cars to keep it solid.

    Sent from...
  4. Replies
    15
    Views
    1,109

    [General] I have a Maxx Jax , well the one that does not...

    I have a Maxx Jax , well the one that does not use rods Dannmar MX6. Its ok, but being 6,2 i always have to have my head tilted to one side while working on something.
  5. Replies
    12
    Views
    841

    I drive mine. When I'm not working on it.

    I drive mine. When I'm not working on it.
  6. Replies
    20
    Views
    1,318

    [Engine] Looks like you have 650 cfm throttle body on...

    Looks like you have 650 cfm throttle body on there. My v8 Z28 had one. I think that's double what you need for a prv. My Nissan ones can only do 350 cfm. Im not sure what the stock Delorean throttle...
  7. Replies
    20
    Views
    1,318

    [Engine] There Nissan 300zx stock throttle bodys

    There Nissan 300zx stock throttle bodys
  8. Replies
    20
    Views
    1,318

    [Engine] I just finished my new setup with bigger throttle...

    I just finished my new setup with bigger throttle bodys. I'm liking them. They may not be practical for my car but i love the throttle response.
  9. Replies
    12
    Views
    812

    I have Printed ABS parts under the hood of my...

    I have Printed ABS parts under the hood of my Marty Toyota for about 4 years now in south Texas. There not showing any deformation from heat. PLA on the other hand, yea that will mess up in heat. I...
  10. Replies
    12
    Views
    812

    I 3D printed some vent tube holders to keep the...

    I 3D printed some vent tube holders to keep the vent tubes open so i could slide the vents in them. But i have not posted the stl. I fought this for years.
  11. Replies
    18
    Views
    1,384

    [Fuel] My pump did this and what helped a bit was to...

    My pump did this and what helped a bit was to make sure the return fuel line inside the tank sprays on to the fuel pump.
  12. Replies
    8,004
    Views
    1,264,804

    [General] Yea. I forgot i was testing them and got on the...

    Yea. I forgot i was testing them and got on the freeway. I was tuning my EFI. It was still there. The breeze in the car was much better. Also they have zero infill for testing but held together fine....
  13. Replies
    8,004
    Views
    1,264,804

    [General] I needed a little more fresh air in the cockpit....

    I needed a little more fresh air in the cockpit. So i test printed a scoop to see if it worked.
  14. Replies
    8,004
    Views
    1,264,804

    [General] Finally added some bigger throttle bodies to my...

    Finally added some bigger throttle bodies to my EFI intake. Made some new fuel rails and add PTFE fuel lines.
  15. Replies
    2
    Views
    626

    Thanks. I'm putting trottlebodys on the towers of...

    Thanks. I'm putting trottlebodys on the towers of the intake manifold. Even though the stock one will still work for what i'm doing the clearance will very tight. I was hoping someone here would have...
  16. Replies
    2
    Views
    626

    Delorean thermostat housing

    Does any one know if there is different thermostat housing that will fit the Delorean. I need one that does not point to the ac compressor, but more toward the back driver side of the car. Thanks
  17. Replies
    9
    Views
    1,045

    [General] I personally run a lower psi thermostat as a car...

    I personally run a lower psi thermostat as a car gets older. After all the cycles of getting hot and cold and metals expand and contracting. Pressure in the cooling system will weep water past some...
  18. Replies
    4
    Views
    824

    [Fuel] High pressure rubber line lasted about 17 years...

    High pressure rubber line lasted about 17 years for me. Alcohol in the gas dissolved the rubber from the inside out.
  19. Replies
    66
    Views
    19,398

    I have ordered all kinds of stuff from him over...

    I have ordered all kinds of stuff from him over the 20 plus years i have had my Delorean. I never had a problem. But i have not had any problems from any vendors of Delorean parts. Guess i'm just...
  20. Replies
    28
    Views
    7,929

    [For Sale] Thought i would go ahead and buy one of your...

    Thought i would go ahead and buy one of your filters since you use a image of my dirty filter. lol
  21. Replies
    36
    Views
    7,968

    [Wanted] I have been dreaming about a LS motor in my...

    I have been dreaming about a LS motor in my Delorean ever since i saw this at sema.
  22. Replies
    88
    Views
    16,909

    Lol

    Lol
  23. Replies
    2
    Views
    926

    [General] i just picked up one of these....

    i just picked up one of these.
    http://tinyurl.com/qcgznrv
  24. Replies
    19
    Views
    6,395

    I will try later to remove it and take a few...

    I will try later to remove it and take a few pictures of my bracket and the slot i made.
  25. Replies
    19
    Views
    6,395

    I think when i ordered it from the counter i said...

    I think when i ordered it from the counter i said a 85 tpi camaro. As far as connecting the arm i saw the angle i was going to install it then grinded a slot in the stock part to match up with the...
Results 1 to 25 of 74
Page 1 of 3 1 2 3