Search:

I messed up once and over tightened the lug nuts. I tried everything to loosen then and ended up having to drill out the lugs.

It was just lots of oil and time sitting there drilling. It...

Thank you, this is exactly what i did!!! i am high fiveing my self lol

When i was trying to bleed the clutch after replacing the fluid, i noticed my master cylinder was not releasing all the way. It was stopping about 1\2 inch from where it was suppose to.

So i took...

So the pins were bad, and i replaced them. That helped a lot.

but now the issue is back. I am going to replace the DOT4 Brake fluid. I am thinking there is contamination in there and that is...

I am thinking about selling mine. After 5 years i think i am ready to move on. That being said, i know there is no way i am not going to regret selling it at some point down the road. I have...

I used one in my car. All the holes line up and it plugs in. The one on the car was fired in side, and so i replaced it. i didn't see a change in anything.

I had all the same issues. I replaced everything i could think of and find. Nothing worked for me.

I ended up making a switch that jumpers the cold stat valve. I wired it from the fuse box...

What is the best way to remove the old leaking seal?

Can i use a breaker bar to remove the nut?

If i cant find the special tool, can i put the car in 1st while it is on the ground? Is that...

I went through problems with mine also.

Make sure it is in "tune" I paid a local garage to make it smog legal.

I installed a switch across my cold start value. I used the relay terminal in the...

I was thinking of black vinyl wrapping the edges of the car. So like the top of the front fenders and a little on the hood. The normal places people run there dirty mitts on the car. lol

I...

I dont know how likely this is. But 2 things come to mind.

I had a similar issue with my clutch petal. It ended up being the linkage was worn out and i wasn't getting the full push of the petal....

I saw this and just wish nothing but bad things for that POS car thief!!!



http://www.latimes.com/local/lanow/la-me-ln-carjacker-delorean-pursuit-santa-monica-20160915-snap-story.html

I was pumping gas at a corner station.

There was some guy at the traffic light, in a pickup truck yelling " Where's the flux capacitor"

I never looked up, just played like i heard nothing.

45106

So i bled the lines again. I checked to make sure the line was not touching the exhaust.

It was baffling me, so i looked at the linkage a second time.

I think these pins are bad. I...

So Again it happened today, i could not make it around the block before the DAM clutch lost pressure,or sucked air. I had the clutch feeling perfect cold, and as soon as it warms up. it just lost...

I just replaced the O ring by my slave cylinder. It was copper and i replaced it with a newer copper washer.

If this doesn't work, i was thinking about using DOT 5.1 break fluid.

My...

So it happened again this weekend. I drove it, and the next day the clutch was limp.

I took the clutch master cylinder apart and cleaned it.

I think it was binding inside the sleeve and...

I have the same problem. My heater core has not be connected for 3 years. i blew out all the old coolant.

I still have the window fog, and it comes back every few days after cleaning it. ...

After you replaced the radiator, did the head gasket leak come back?

I added it to mine after a $9000 quote. I was at the "what do i have to loose" point.

It worked and now i watch for the...

I was going to start my next fix on the car.

i am pretty sure the windshield washer pump is bad. I cant really test that it is getting voltage since it is covered.

All but one bolt that...

So all the talk of no fire wall has me asking the question....

Do we have any options?

Is there a flexible material we can add to the interior of the engine compartment?

Is there a fire...

So my big question is the smog test with historic plates. Do you still need to smog the car when you have historic plates?

Right now i still have to smog my car. i pay just under $100 a year for...

I never adjusted the linkage on the clutch petal. it is an old car, so it could be done by the previous owner.

From what i can see, you press the petal down and the bar going into the master...

I have the Stainless steal clutch line. the master and slave cylinder are only 5 and 4 years old.

i will try replacing the fluid, and see if that helps.

Is there any way the "check...

Hi all

So yesterday was a hot day in the valley again and today after my car cooled down the clutch was soft to the touch. So i was reading some other posts and it seam that inside the master...