FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds; generated 44 minute(s) ago.

  1. Replies
    34
    Views
    838

    [General] I think most of us that have been in a parade...

    I think most of us that have been in a parade drive it with the doors open. So a paved road at 5 MPH is probably safe.
  2. Replies
    169
    Views
    20,204

    Like always the photo just can not get the true...

    Like always the photo just can not get the true colors of LEDs. I do see I need to fix the small green dot above and to the right of "MAX". I also want to look into covering the two push button...
  3. Replies
    169
    Views
    20,204

    So what kind of plastic do you think the OEM...

    So what kind of plastic do you think the OEM faceplate was made of? I just ordered some ABS filament to try another HVAC face plate made with that. ABS works to higher temps than PLA.
  4. Replies
    169
    Views
    20,204

    Decal Alignment

    Alignment cylinders worked out perfect. These are 1.416" dia. which makes it snug on the DMCH decal. My printed faceplate I made the holes 0.010 smaller so I could sand them on my oscillating drum...
  5. Replies
    169
    Views
    20,204

    Trying to get something engineered so I can place...

    Trying to get something engineered so I can place the decal exactly in the correct position. I can only think of using the two push button holes for alignment. The holes in the decal are 1.420" so...
  6. Replies
    20
    Views
    544

    [Fuel] You won't be able to buy acetone in California.

    You won't be able to buy acetone in California.
  7. Replies
    56
    Views
    5,141

    [General] Yes the OEM pins are not really interchangeable...

    Yes the OEM pins are not really interchangeable with the AMP connector. My pin extractor does not work with the AMP pins.
  8. Replies
    169
    Views
    20,204

    Well I'm going with the idea to print the HVAC in...

    Well I'm going with the idea to print the HVAC in black and have made cutouts for the decal illumination areas. It would probably work without filling those cutouts with clear epoxy. The stock face...
  9. [Suspension] It looks like only 0.028" difference so I would...

    It looks like only 0.028" difference so I would think the casing is still there.
  10. [Suspension] Did you check if the old one has been bent out of...

    Did you check if the old one has been bent out of round. Measure it at 90 degrees from the first measurement.
  11. Replies
    5
    Views
    229

    [General] Yes the inertia switch is what I mean. The door...

    Yes the inertia switch is what I mean. The door lock ECU is a black box (if stock) mounted on the relay compartment metal plate. It has a 9 pin connector on wires to that black box.
  12. Replies
    5
    Views
    229

    [General] If your impact sensor is triggered it will unlock...

    If your impact sensor is triggered it will unlock if you have the door lock ECU installed.
  13. Replies
    169
    Views
    20,204

    I did get that clear filament and printed an HVAC...

    I did get that clear filament and printed an HVAC panel. Only real problem was that 0.71 deg offset from square so the two standoffs are offset to much. I'm not sure if the clear will block the...
  14. Replies
    169
    Views
    20,204

    Ran into another problem. My 4 corner standoffs,...

    Ran into another problem. My 4 corner standoffs, the top 2 were shifted to the right. Checked my design a 100 times and then thought to use a square to check the print. The print is not printing...
  15. Replies
    169
    Views
    20,204

    Thanks. I plan to test to 140 F or above.

    Thanks. I plan to test to 140 F or above.
  16. Here is a interesting tidbit of info. Well after...

    Here is a interesting tidbit of info. Well after about a week with it holding around 44 PSI, I released the pressure and it leaked out the gas pretty slowly (about 30 seconds). I could also hear...
  17. Replies
    169
    Views
    20,204

    There is no mechanical needs for the HVAC. Just...

    There is no mechanical needs for the HVAC. Just my concern is the bond between the decal and faceplate. I do plan to try PETG and ABS to play with. What do you think the max temp inside the cabin...
  18. Replies
    169
    Views
    20,204

    Got some black pro tough PLA from Matterhackers. ...

    Got some black pro tough PLA from Matterhackers. Ran my test print and it worked nice. This stuff runs at 210 C and 60 C bed where as the PLA that came with my unit runs at 190 C and 50 C bed.
    ...
  19. Replies
    169
    Views
    20,204

    Learning how to get a good print. What I finally...

    Learning how to get a good print. What I finally did was cut a one inch square of where my HVAC print was having problems. Then I could modify the options in the print slicer. The options are so...
  20. Replies
    12
    Views
    419

    [Engine] If it was just the added engine load and your...

    If it was just the added engine load and your idle system could not keep up that with the AC your idle would drop. So my guess is the problem is electrical. What is your car voltage when the AC is...
  21. Replies
    169
    Views
    20,204

    Well I figured it out. I had to select expert...

    Well I figured it out. I had to select expert options with my slicer and set the minimum area to use infill to a very large number (100,000 mm2). I answered my own question when it worked on my...
  22. Replies
    12
    Views
    419

    [Engine] My idle ECU can bump the idle speed an extra 100...

    My idle ECU can bump the idle speed an extra 100 RPM (with AC on) if you have it. Check if you have a blue wire coming off the idle ECU.
  23. Replies
    169
    Views
    20,204

    Well I still have a problem printing the HVAC. ...

    Well I still have a problem printing the HVAC. Looks like the first layer prints good at 24 mm/sec then it prints at 48 mm/sec still looking pretty good then it starts lousy printing of layers at 60...
  24. Replies
    21
    Views
    995

    [Suspension] The sharpie test is good. I would think another...

    The sharpie test is good. I would think another test is to just sit the taper into the reamed location and measure deflection on each end. A little hard to do with ball joints though. I wonder if...
  25. Replies
    21
    Views
    995

    [Suspension] https://www.carbideanddiamondtooling.com/Reamer.st...

    https://www.carbideanddiamondtooling.com/Reamer.standard.ball.joint.taper.motorcycle.reamers
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4