FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds; generated 41 minute(s) ago.

  1. Replies
    26
    Views
    11,688

    [Electrical] With the OEM ECU the module circuit is powered by...

    With the OEM ECU the module circuit is powered by the small purple wire. The actuators get powered by the red wire from the beaker.
  2. Photo reminds me that I recently fixed my hood...

    Photo reminds me that I recently fixed my hood light from falling out all the time. About 10 layers of masking tape on one end of clear lens and now it holds in very nicely. I think a lot of owner...
  3. Replies
    26
    Views
    11,688

    [Electrical] There are only 2 wires for the door switches. ...

    There are only 2 wires for the door switches. One is grounded when both doors are locked and floats when unlocked. The other wire is grounded when both doors are unlocked and floats when locked. ...
  4. Replies
    103
    Views
    27,243

    [General] Agree. The GM module gives you better dwell...

    Agree. The GM module gives you better dwell (less power consumed at idle) and current limiting (6 amps max) but still can run OEM unit with about 1.5 ohm coil.
  5. Replies
    103
    Views
    27,243

    [General] Yes. Don't keep running it like that with a 0.40...

    Yes. Don't keep running it like that with a 0.40 ohm primary coil.
  6. Replies
    103
    Views
    27,243

    [General] The white/yellow goes to the coil. The white...

    The white/yellow goes to the coil. The white wire gets 12 volts with the key on (from AUX relay). So you would connect the white wire to the white/yellow wire and tape off (or remove) all other...
  7. Replies
    103
    Views
    27,243

    [General] The ignition coils normally need about 6 amps of...

    The ignition coils normally need about 6 amps of current when running. The use of a resistor was the normal design so when cranking a cold engine you could get that 6 amps when the battery voltage...
  8. Replies
    16
    Views
    651

    [General] I would think where the sheet does sharp bends it...

    I would think where the sheet does sharp bends it could thin that much.
  9. Replies
    895
    Views
    116,624

    Look at this thread. Start at Post #85 if you...

    Look at this thread. Start at Post #85 if you don't want to read the whole thing.

    https://dmctalk.org/showthread.php?13649-Ignition-ECU-operation-HEI/page9
  10. Replies
    6
    Views
    257

    [General] Thanks. Stopped in Harbor Freight and they don't...

    Thanks. Stopped in Harbor Freight and they don't have much for 3/4" drive unless you what to buy a full set. I just picked up a 3/4" to 1/2" adapter and a 32 mm 1/2" drive impact socket. You would...
  11. Replies
    6
    Views
    257

    [General] Outer Drive Shaft hub

    What socket size it the outer drive shaft hub (the one that requires 270 ft/lbs). I need to have that socket and an extension for my 3/4 torque wrench on hand.
  12. Replies
    7
    Views
    288

    [General] Does your car hold the idle at 775 RPM? The idle...

    Does your car hold the idle at 775 RPM? The idle ECU opens the idle motor at power on so that should provide enough throttle to start without using the gas pedal.

    The warm up regulator makes the...
  13. Replies
    35
    Views
    3,241

    Hard to see in that photo but I think I see...

    Hard to see in that photo but I think I see uneven spacing which has shown the springs are a problem.
  14. Replies
    35
    Views
    3,241

    With all those symptoms, my guess is you have...

    With all those symptoms, my guess is you have leaking deceleration springs. Did you look at springs?

    Here is a photo of bad springs.
  15. Replies
    35
    Views
    3,241

    I used locktite to lock that holding washer in...

    I used locktite to lock that holding washer in but as long as the correct O-ring is installed it should make a good seal. I also put some grease on the copper pipe which may also help with sealing.
  16. Replies
    10
    Views
    648

    [Heat & A/C] It's best to compare vent temps not using...

    It's best to compare vent temps not using re-circulation (max). With max air you can get very cold running a long time in the shade. With outside air it's a more stable test of how well the system...
  17. Replies
    0
    Views
    294

    [General] New Dome light "relay"

    I've designed the electronics in the dome unit to work with the Super Bright LEDs with switching regulators. I've tested with the switching LEDs in both dome lights and elsewhere (hood). Still...
  18. Replies
    35
    Views
    3,241

    Stock idle ECU always tries to hold 775 RPM. ...

    Stock idle ECU always tries to hold 775 RPM. Does not matter hot or cold, idle switch on or off.

    The idle switch just helps the stock idle ECU control timing when you release throttle quickly. ...
  19. Replies
    129
    Views
    11,642

    [General] As I suspected, the CAT would not blow out on...

    As I suspected, the CAT would not blow out on it's own.
  20. Replies
    895
    Views
    116,624

    You had a 50/50 chance of putting the sealer on...

    You had a 50/50 chance of putting the sealer on the other side.
  21. Replies
    13
    Views
    913

    [General] I think you get that with or without a CAT. Our...

    I think you get that with or without a CAT. Our engines run very rich when cold.
  22. Replies
    13
    Views
    913

    [General] I agree. My CAT is hollow and I don't think it...

    I agree. My CAT is hollow and I don't think it smells.
  23. Replies
    9
    Views
    793

    Yes that is the two pin connector that feeds the...

    Yes that is the two pin connector that feeds the diagnostic port.
  24. Replies
    40
    Views
    6,192

    [Engine] Glad you got it working. Testing with a meter...

    Glad you got it working. Testing with a meter does not always show the problem. Your 4 ohms with the meter is probably worse when the one amp of CSV current is flowing through that connection.
  25. Replies
    24
    Views
    2,092

    [Fuel] That proves your meter is working reading the...

    That proves your meter is working reading the correct value.

    You normal readings should be swinging around 35 to 45 degrees on the 4 cylinder scale. So your 65 reading is telling you it needs to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4