FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Boxbot

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    3,888

    [For Sale] PM Sent.

    PM Sent.
  2. Replies
    19
    Views
    1,849

    [Engine] Excellent thread guys. I thought the pulleys or...

    Excellent thread guys. I thought the pulleys or the belts were squealing, but the W pipe just wasn't tight enough. Thanks for the help with my problem du jour.
  3. Replies
    5
    Views
    449

    [Frame & Body] Front and rear fascia paint/straightening

    My car is now in more or less mechanically sound condition.

    The paint on the front and rear fascias is really letting it down, however. It looks like they were both resprayed at some point, but...
  4. Replies
    3
    Views
    379

    [Wanted] https://deloreanindustries.com/throttle-shield-cov...

    https://deloreanindustries.com/throttle-shield-cover-stainless/
  5. [General] 65 PSI references high control pressure NOT low...

    65 PSI references high control pressure NOT low primary pressure.
  6. [General] If it's not the CPR or the return hose, what else...

    If it's not the CPR or the return hose, what else could it be? Could CPR need to be rebuilt even if not clogged?
  7. [General] That's where we started. I mentioned on page 7...

    That's where we started. I mentioned on page 7 they pulled and examined the CPR (warm up regulator) and said it looks like new. They pulled the return hose but control pressure is still too high.
    ...
  8. [General] From mechanic: The control pressure out of the...

    From mechanic:

    The control pressure out of the warm up regulator is showing that pressure, which the spec should be 49-53 PSI. We should have been seeing 345-375 kPA at the temperatures we were...
  9. [General] Not to second guess Dave, but can anyone confirm?

    Not to second guess Dave, but can anyone confirm?
  10. [General] 450 Kpa.

    450 Kpa.
  11. [General] Return line is clear. Pressure is still too high....

    Return line is clear. Pressure is still too high. Recommended they look at primary pressure regulator per your comments. Any other known culprits?
  12. [General] Shop pulled and examined the CPR and say it is in...

    Shop pulled and examined the CPR and say it is in good shape. They diagnosed the fuel pressure as being too high and are trying to diagnose.
  13. [General] Car does run ok as soon as it starts to warm up...

    Car does run ok as soon as it starts to warm up (when needle moves even slightly off the bottom mark) but then the lack of throttle is replaced with a noticeable idle hunt that I didn't have...
  14. [Electrical] I experienced bulb failure with some of my...

    I experienced bulb failure with some of my DeLoreanGo bulbs. They couldn't have been better about replacing.

    I noticed, however, that the front amber LEDs were simply not nearly bright enough...
  15. [General] So today, the car didn't want to rev when cold....

    So today, the car didn't want to rev when cold. If I pushed the gas pedal, the revs dropped and it threatened to stall. Stayed that way until the temp gauge moved off the bottom. Felt like the car...
  16. [General] Responses transposed below: 1) If you have...

    Responses transposed below:

    1) If you have the Stage II cams, it will hunt more than a stock PRV. If you have the stock cams and it is hunting recheck the idle motor system.
    Stock cams. Will...
  17. [General] This car continues to try my patience. Fuel tank...

    This car continues to try my patience. Fuel tank cover bolted up with proper hardware, fuel filter reattached to frame, new front pass tie rod end, new rear pass wheel bearing, new brake lines, new...
  18. Replies
    17
    Views
    1,925

    [Frame & Body] No hole. No idea why the passenger side is set up...

    No hole. No idea why the passenger side is set up correctly but the driver's is not. Will have to drill and place the pin through.

    I shall draft a strongly worded letter to my local DeLorean...
  19. Replies
    17
    Views
    1,925

    [Frame & Body] At the recent DMA event, it was noted that my...

    At the recent DMA event, it was noted that my driver's side castle nut was missing its cotter pin. I tried to install one today and discovered there's no hole to put the pin through! What should I...
  20. Replies
    8,020
    Views
    1,279,401

    [General] Headed back to the shop tomorrow for a laundry...

    Headed back to the shop tomorrow for a laundry list of (hopefully) minor stuff.

    In the meantime, I replaced my toasted vacuum label for a shiny new one.

    5994659947
  21. Replies
    18
    Views
    4,840

    Deleted

    Deleted
  22. Replies
    10
    Views
    833

    [Wanted] Thanks. The generic one is "synthetic materials"...

    Thanks. The generic one is "synthetic materials" and looks very plastic - which I would expect at that price point. Either way, I would still need the adapter, though, which doesn't appear to be...
  23. [General] Welcome and congrats! What about fuel...

    Welcome and congrats!



    What about fuel pump and fuel hoses? The original pumps and rubber are long past their sell by date.



    Take a peek at the master clutch cylinder by the clutch...
  24. Replies
    8,020
    Views
    1,279,401

    [General] Where did you find them and how do you like them?...

    Where did you find them and how do you like them? I'm used to Audis, which use them to provide a small bit of ambient lighting around the cabin and I thought about installing some.
  25. Replies
    7
    Views
    616

    Uh oh. 59911

    Uh oh.

    59911
Results 1 to 25 of 123
Page 1 of 5 1 2 3 4