FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: FABombjoy

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    510

    [Electrical] Axial leaded caps went out of style in the 80's. ...

    Axial leaded caps went out of style in the 80's. I would be SHOCKED (ha) to see one in a modern design - they're somewhat available still but typically at much higher cost than leaded or surface...
  2. Replies
    60
    Views
    3,903

    I'm surprised that all of the new and improved...

    I'm surprised that all of the new and improved tail light PCBs haven't been made with layouts that would facilitate plug & play sequencers.
    Like, integrating the pads for a sequencing connector and...
  3. Replies
    26
    Views
    1,695

    You don't want big gaps. The injector PW is...

    You don't want big gaps. The injector PW is connected to the VE number on the table but also an interpolation of the surrounding values based on a weight of how far the RPM is from the target...
  4. Replies
    26
    Views
    1,695

    https://imgur.com/a/8CoiYdu That seismograph...

    https://imgur.com/a/8CoiYdu

    That seismograph looking section is an oscillation. Like a guitar string or a bell.
    Oscillation in EFI logs means something isn't set up correctly. K-jet oscillates...
  5. Replies
    139
    Views
    60,735

    Are you asking all 3 of us? My setup requires...

    Are you asking all 3 of us?

    My setup requires no suspension mods, only spacers in the front and adapters in the rear (spacers with integrated studs). 205/45ZR-16 and 245/45ZR-17 tires.
  6. Replies
    26
    Views
    1,695

    Huh? No, that was Owen's issue causing...

    Huh? No, that was Owen's issue causing off-throttle bog :) Your TB is probably fine.

    This is what stock, turbo B28F, and LT1 throttle data looks like (I grabbed the first log I could find from...
  7. Replies
    26
    Views
    1,695

    Yes, not advocating you switch to MAF :D A too...

    Yes, not advocating you switch to MAF :D

    A too large throttle body would emerge in a average plot of TPS vs MAP. If your logs show that a minor change in TPS results in a huge shift upward in MAP...
  8. Replies
    26
    Views
    1,695

    I don't think velocity was the issue. Putting a...

    I don't think velocity was the issue. Putting a 300HP engine throttle body (208.2 CFM) on a 130HP (90.22 CFM) engine and tuning based on MAP caused loss of finite torque control.

    An accel...
  9. Replies
    13
    Views
    791

    Almost certain that you need more base throttle...

    Almost certain that you need more base throttle opening.

    Right at the end of the log you're at 194F, indicating warmed up. Your CL idle target RPM is 990 (base plus AC idle up). Your IAC is open...
  10. Replies
    13
    Views
    791

    Probably a good idea to add the negative...

    Probably a good idea to add the negative conditions in as well.

    VEAL is useless without tuning the delay table but your delay table still looks stock. I can't emphasize enough that VEAL will do...
  11. Replies
    13
    Views
    791

    I see you still don't have TPS :) It's tough to...

    I see you still don't have TPS :) It's tough to judge your intentions without knowing what your foot was actually doing, but based on some guessing this is what jumps out immediately:

    Chief cause...
  12. [General] Lets bump your MS thread and continue this there.

    Lets bump your MS thread and continue this there.
  13. [General] Sounds good! To briefly tie ventilated seats...

    Sounds good!

    To briefly tie ventilated seats with this megasquirt non sequitur, I briefly considered tying unused MS3X coil driver outputs to the seat fan PWM in and sending fan control commands...
  14. [General] Even without AC idle-up you shouldn't stall like...

    Even without AC idle-up you shouldn't stall like that. I know that came up in your build thread - did you post a log/MSQ of when it happens? If so send me a link and I can re-review your tune and...
  15. [General] I have the style with carbon wires that criss...

    I have the style with carbon wires that criss cross. You can cut sections out of the middle but I just punched holes through the fabric that holds the wires in place.

    If you cut only sections for...
  16. [General] I'm taking a labor day break, but in short: -A...

    I'm taking a labor day break, but in short:
    -A cheap seat heater kit, cutting a million little holes in the heat pad fabric so air circulation can happen
    -The heater kit switch and driver module...
  17. [General] The STL? Maybe - let me get this setup to a full...

    The STL? Maybe - let me get this setup to a full version 1.0 first :)
    The vent does conflict a little with the battery cover so I'll have to revise it.

    I hope to have both heating & cooling...
  18. [General] Seat Back Modifications Step one was to remove...

    Seat Back Modifications
    Step one was to remove all of the staples and original vinyl from the seat back.

    The vinyl has a foam layer that had turned into sticky dust.

    Rob Grady posted a...
  19. [General] Installation: Seat Upper Seat uppers is a little...

    Installation: Seat Upper
    Seat uppers is a little more challenging.

    It's easier to drill the holes, but with the back installed, that chamber is somewhat airtight if you're trying to move a large...
  20. [General] Installation: Seat Bottoms For the seat bottoms...

    Installation: Seat Bottoms
    For the seat bottoms I installed the fans toward the front, out of the "butt zone" if you will. The holes emerge in front of the big lower rubber seat bottom and can...
  21. [General] Circulation Fans There are some all-in-one seat...

    Circulation Fans
    There are some all-in-one seat circulation kits. They look pretty sketchy to me. The controls look cheap and the fans look cheap. It's a lot more intrusive than a heating kit so...
  22. [General] Seat Bottom Notes These are fairly identical in...

    Seat Bottom Notes
    These are fairly identical in install approach to the stock covers.

    I think the fabric for the metal ribs is too long. With the ribs pulled in to place the metal is right up...
  23. [General] Seat Back Headrest Notes Lots of tricks to get...

    Seat Back Headrest Notes
    Lots of tricks to get the seat back over the headrest. But you can also stuff the headrest into the cover first.

    Two small cuts decapitates the foam from the seat. You...
  24. [General] Seat Back Notes To give the back bolsters...

    Seat Back Notes
    To give the back bolsters definition, the original covers have vertical metal bars that are hog ringed to the "bbq grill". This pulls the cover flush to the foam.

    The Lseat...
  25. [General] Installation I'm just going to wholesale...

    Installation
    I'm just going to wholesale reference the "slip me some skin" PDF article that's floating around out there somewhere.
    For the most part it's totally applicable here with a few...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4