FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Delorean Industries

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. [General] We have been producing stainless frames since...

    We have been producing stainless frames since late 2012 and have far exceeded the number previously produced years ago.
  2. [General] If you have a old pearce frame then yes. The heim...

    If you have a old pearce frame then yes. The heim joints at the end of your trailing arms may be adjustable.
  3. [General] We recommend uppers when correcting the...

    We recommend uppers when correcting the suspension geometry created with the above parts installed. In stock and ready to ship.
  4. [General] We offer a premium solution for this. High...

    We offer a premium solution for this. High tolerance to take out the unwanted deflection present in the plastic bushing. Fully serviceable with the ability to remove and install as many times as you...
  5. Replies
    89
    Views
    21,291

    [General] We will be releasing an updated design shortly....

    We will be releasing an updated design shortly. The Factory design wasn't the best.
  6. [Brakes] No need to cut. Insert lower flange piece first...

    No need to cut. Insert lower flange piece first and then insert stem.
  7. [General] I believe he is working with an older pearce...

    I believe he is working with an older pearce frame configuration.
  8. [Electrical] That time you stopped by and your starter wasn't...

    That time you stopped by and your starter wasn't even bolted in accept for a few cross-threaded standard bolts? :) If the starter happens to be the culprit just let us know and we will warranty it of...
  9. [Brakes] "Better Call Mike"

    "Better Call Mike"
  10. [Brakes] The pad to rotor contact surfaces are glazed....

    The pad to rotor contact surfaces are glazed. Best solution is to either replace pads and machine rotors if in spec and or replace both pads and rotors outright.
  11. [Electrical] Always in stock and will ship first thing in the...

    Always in stock and will ship first thing in the am. We can next day this to you as well.

    https://deloreanindustries.com/120-amp-alternator-kit-complete/
  12. Replies
    43
    Views
    3,701

    [General] 60959

    60959
  13. [Suspension] Not from us. But thanks Michael.

    Not from us. But thanks Michael.
  14. Replies
    45
    Views
    2,391

    [General] 60922

    60922
  15. Replies
    45
    Views
    2,391

    [General] The best we produced on an engine dyno with a...

    The best we produced on an engine dyno with a stock PRV using K jet was 127 with a converter (stock exhaust) 135 with a test pipe.


    This was back during the development years.

    60919
  16. Replies
    45
    Views
    2,391

    [General] This is why we provide specs for what we build....

    This is why we provide specs for what we build. Standard on anything forced induction and available per request on EFI and naturally aspirated installs.
  17. Replies
    45
    Views
    2,391

    [General] 89 is the average number from a five speed

    89 is the average number from a five speed
  18. Replies
    45
    Views
    2,391

    [General] Stage II dyno chart below. We tested all...

    Stage II dyno chart below. We tested all available products on the market to bring the actual numbers to the surface. Feel free to calculate your "drive train loss" to reach 197 BHP. :)

    60917
  19. Replies
    8,020
    Views
    1,279,401

    [General] Fuel rails with injectors ...

    Fuel rails with injectors

    https://deloreanindustries.com/spec-efi-fuel-rail-set-w-injectors/


    Fuel rails stand alone

    https://deloreanindustries.com/delorean-dpi-efi-fuel-rail-set/

    60883
  20. [Wanted] We no longer sell K jet parts other than our fuel...

    We no longer sell K jet parts other than our fuel lines over the counter. The cars are too temperamental with age and blending premium Bosch parts with the Brand x components in the market place is a...
  21. Replies
    12
    Views
    707

    [General] The issue is not with our shrouds. They are a...

    The issue is not with our shrouds. They are a precision component with high tolerances held. The disclaimers for the above mentioned radiator on Delorean go is plenty to substantiate where the...
  22. [Frame & Body] We have our own design but supply this to rob...

    We have our own design but supply this to rob along with a few others products he once made such as door strut reinforcement brackets which have been updated as well.

    Our shift boots are cut,...
  23. [Frame & Body] goes behind the carpet for your seat belt...

    goes behind the carpet for your seat belt mounting point. bushing facing fiberglass.
  24. Replies
    29
    Views
    1,645

    [Engine] Rtv is not right for this. You need to use...

    Rtv is not right for this. You need to use hylomar to dress the gasket.
  25. Replies
    8
    Views
    642

    [Wanted] We can provide you with a good used set of our...

    We can provide you with a good used set of our premium lines. We have takeoff sets from owners seeing the light and moving to EFI available at a discounted rate.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4