FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Jason

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Liner Seals

    by Jason
    Replies
    68
    Views
    2,592

    [Engine] When I rebuilt my engine, the advice I got from...

    When I rebuilt my engine, the advice I got from DPI was...



    Though this was with new liners from DPI. I don't know if that makes any difference.
  2. Thread: 3D printer

    by Jason
    Replies
    40
    Views
    1,777

    Yea, Blender will do that. And yes, you'll have...

    Yea, Blender will do that. And yes, you'll have to go through a whole bunch of tutorials to figure out how to do it.
  3. Thread: 3D printer

    by Jason
    Replies
    40
    Views
    1,777

    Blender really isn't a good tool for part design....

    Blender really isn't a good tool for part design.

    I think FreeCAD is the best of the open source tools, though it's kind of hard to learn and seem to behave strangely whenever I try to use it....
  4. Replies
    25
    Views
    3,303

    Does the heat and AC work?

    Does the heat and AC work?
  5. Replies
    66
    Views
    6,557

    25 years. 28K miles when I bought it. Now at...

    25 years.

    28K miles when I bought it. Now at almost 230K miles.
  6. Thread: Chain noise

    by Jason
    Replies
    31
    Views
    1,670

    [Engine] Fan on the alternator hitting something?

    Fan on the alternator hitting something?
  7. Replies
    7
    Views
    627

    [Suspension] No pin. It was a reasonably thick nut with a...

    No pin. It was a reasonably thick nut with a nylon locking insert.

    The ball joints on the two sides were different. They were installed back when it was discovered that DMCH's reproduction ball...
  8. Replies
    7
    Views
    627

    [Suspension] is this control arm still good?

    While I was driving at about 35mph the left front hub carrier separated from the lower ball joint. Wheeeee…. Steering with 1 wheel is "interesting". The nut either broke or somehow unscrewed. The...
  9. Replies
    12
    Views
    939

    Some stuff I've done... ...

    Some stuff I've done...

    http://dmctalk.org/showthread.php?9137-3D-Printing-and-Your-Delorean&p=203072&viewfull=1#post203072
    ...
  10. https://www.youtube.com/watch?v=v0UjpGcJyww ...

    https://www.youtube.com/watch?v=v0UjpGcJyww

    It's hard to tell because of the camera frame rate, but the crankshaft and accessories are normally spinning clockwise.
  11. It's the compressor shaft and clutch assembly....

    It's the compressor shaft and clutch assembly. From the way it moves and watching the high and low side pressures its pretty clear it's back pressure pushing the compressor backwards.

    The reason...
  12. In this case its not an illusion. It's definitely...

    In this case its not an illusion. It's definitely spinning backwards.
  13. Non Delorean AC question. Compressor runs backwards when clutch disengages

    While trying to track down a leak in the AC system in my Toyota Sera, I noticed that when the AC clutch disengages the compressor slowly spin backwards for 5 to 10 seconds. Does anyone know if this...
  14. Replies
    34
    Views
    2,656

    [General] Does anyone have an agreed value policy without...

    Does anyone have an agreed value policy without any driving restrictions, and if so with which insurance company?
  15. Replies
    264
    Views
    55,128

    The parts experience is a lot different from the...

    The parts experience is a lot different from the DeLorean.

    New rear brake cylinders in stock at the local parts store. $13 each.

    Water pump: $40 including free overnight delivery.
  16. Replies
    264
    Views
    55,128

    I just picked up this... 58508 1991 Toyota...

    I just picked up this...
    58508

    1991 Toyota Sera. Right hand drive.
  17. Replies
    7
    Views
    700

    https://www.youtube.com/watch?v=7MzRdz3WP2M&t=102s

    https://www.youtube.com/watch?v=7MzRdz3WP2M&t=102s
  18. Replies
    402
    Views
    103,198

    There should be three bolts for the starter.

    There should be three bolts for the starter.
  19. Replies
    7
    Views
    700

    https://www.instagram.com/p/Bo7YEySAveg/ 58324 ...

    https://www.instagram.com/p/Bo7YEySAveg/
    58324

    I don't know who took the picture, but it's my car in the background.
  20. Replies
    43
    Views
    10,067

    I 3D printed some custom ductwork so that I could...

    I 3D printed some custom ductwork so that I could route the center A/C vents to the sides of the center console to make room for a 2 din head unit while still retaining correct control of the center...
  21. Replies
    12
    Views
    1,635

    [General] I just put one in my car, and also used a similar...

    I just put one in my car, and also used a similar kit from DMCH on the rest of the center console.

    58153

    58152

    I did the install myself, and had no previous experience doing this sort of...
  22. Replies
    14
    Views
    1,498

    [General] I "restored" my headliner panels by gently...

    I "restored" my headliner panels by gently scraping them clean and then painting them with fiberglass resin.
  23. [Heat & A/C] How much oil to add when replacing the evaporator?

    If replacing just the AC evaporator and accumulator, and not flushing the system, how much oil should be added before putting back the refrigerant?

    The AC system was evacuated and opened to remove...
  24. Replies
    20
    Views
    2,077

    [Frame & Body] I just recovered my rear panels. I shopped around...

    I just recovered my rear panels. I shopped around locally for someone to do them, but no one wanted to touch them, so I decided to try it myself.

    My panels had a single piece of vinyl covering...
  25. Replies
    4
    Views
    395

    [Heat & A/C] To answer my own question... After struggling...

    To answer my own question...

    After struggling with this for way too long, I put the boot across a reversed woodworking clamp, extended the clamp to stretch out the boot, and let it sit that way...
Results 1 to 25 of 176
Page 1 of 8 1 2 3 4