Search:

Type: Posts; User: DMC-81

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    122

    [Suspension] If it helps: I lowered mine to within an inch...

    If it helps:

    I lowered mine to within an inch of the design height. I didn't "slam" the front down because of my concern about hitting the fender (personal preference).

    When I had the alignment...
  2. Replies
    17
    Views
    378

    [Electrical] +1. Here are a couple pictures from that angle: ...

    +1. Here are a couple pictures from that angle:

    http://dmctalk.org/attachment.php?attachmentid=43728&d=1466110404

    http://dmctalk.org/attachment.php?attachmentid=43729&d=1466110476
  3. Replies
    6
    Views
    268

    [Fuel] I’m all for originality, but unless you have a...

    I’m all for originality, but unless you have a museum car, I strongly recommend upgrading to the all in one fuel pump module from DMC. I have had one in my car since I purchased it in 2013. I live in...
  4. Thread: Fuel Tank

    by DMC-81
    Replies
    25
    Views
    2,428

    [Fuel] +1. But I throttle the handle halfway all the...

    +1. But I throttle the handle halfway all the time during the fill up. If I don't, many times the fuel handle automatically shuts off. It's a small tank so it doesn't take that much longer.
    ...
  5. Replies
    66
    Views
    3,078

    Hooray! Congrats!

    Hooray! Congrats!
  6. Replies
    2
    Views
    120

    [Heat & A/C] You'll need something to connect the high...

    You'll need something to connect the high pressure switch and the high pressure relief valve to. That is assuming you have the "very early" AC system without the Hub Dave mentioned above, which...
  7. Replies
    7,645
    Views
    1,154,911

    [General] Cool. Good luck with the frame off restoration. ...

    Cool. Good luck with the frame off restoration. :wrenchin:
  8. Replies
    12
    Views
    650

    [General] :hihi2: The host described it as "Mississippi...

    :hihi2: The host described it as "Mississippi Engineering" .

    Apologies to anyone living in that state.
  9. Replies
    10
    Views
    399

    [Transmission 5-Speed] If it helps, here is a picture of the angle of...

    If it helps, here is a picture of the angle of the gearbox mated:
    http://dmctalk.org/attachment.php?attachmentid=55798&d=1522255258

    Make sure the engine is rigidly supported in its normal...
  10. [Engine] Yeah, I know.:) I highlighted Nick's response...

    Yeah, I know.:) I highlighted Nick's response again as unfortunately, I've seen this movie before.
  11. [Fuel] Appendix: Heat Shrinking the Hoses:

    One other thing, and as mentioned, I bought these hoses previously before DeLoreanGo began offering pre-wrapped hoses. So I wrapped the return hose myself and wanted to show you how easy it is:

    I...
  12. [Engine] Lol. I think it has, by a mechanical engineer...

    Lol. I think it has, by a mechanical engineer who just happened to design and commission both a bulletproof coupler and a one-piece input shaft for our gearbox. Of the 2 arguments, I tend to...
  13. Thread: Introductions!

    by DMC-81
    Replies
    705
    Views
    174,196

    Sticky: Welcome to the forum! There are very helpful...

    Welcome to the forum! There are very helpful people here and a wealth of knowledge. Congrats on the arrival of your child.
  14. Replies
    10
    Views
    399

    [Transmission 5-Speed] +1. I used 4 M10 x 80mm bolts . If you get the...

    +1. I used 4 M10 x 80mm bolts . If you get the gearbox correctly aligned with the engine, it should not hang up.
  15. Replies
    653
    Views
    71,852

    Something to look for when removing the variable...

    Something to look for when removing the variable orfice valve: It may be clogged because of a bend in the tube that it sits in. It has a brass pin in the middle that helps make the variation work. If...
  16. [Fuel] Thanks Shane! I am glad it is helpful. ...

    Thanks Shane! I am glad it is helpful.

    ----------

    FV Hoses Installed:

    Below is the routing I used for the hoses on the frequency valve. I decided to direct the high pressure hose on the...
  17. [Fuel] Assembling the New Low Pressure hose:

    The low pressure hose is mostly braided SS but has a short piece of rubber hose. I see that you can now optionally send DeLoreanGo your FV and have it permanently fastened to the hose (like OEM)....
  18. [Fuel] Frequency Valve

    Here is the Frequency Valve removed. Stamped on it I see the Bosch part number: 0 280 150 300 and the DMC number is: 102395 . The high pressure line is 102400 and the low pressure line is integrated...
  19. [Fuel] Return Hose Removal continued

    Thanks Jonathan!

    -------------------
    Return Hose Removal continued:

    I separated the 8mm cutting ring/”Olive”/ bulk ring (106980) from the metric tube compression adapter (106994) . I applied...
  20. [Fuel] Thanks Austin! Although I think this task is a...

    Thanks Austin! Although I think this task is a one person job and I'm posting after the fact. :wrenchin:

    ----------
    Here is the clamp and electrical connection disconnected:...
  21. [Fuel] Replacing the Frequency Valve and Return hoses

    Taking advantage of the cooler weather these past few weeks, I decided it is time to replace the 3 remaining fuel lines with my previously purchased DeloreanGo braided stainless steel replacements....
  22. Replies
    5
    Views
    224

    [Fuel] Hi. I didn't have a bent accumulator fitting on...

    Hi. I didn't have a bent accumulator fitting on my new unit, but I found the old accumulator had a bent one as shown below. It was bent towards the other outlet):
    ...
  23. Replies
    653
    Views
    71,852

    Congrats on getting the car's cooling system to...

    Congrats on getting the car's cooling system to this point. :thumbup:

    One thing I always do in a "low slung car" is enter and leave steep grade driveways/ramps at an angle, sometimes at 45...
  24. Clutch Stiffness

    I can attest to the fact that the stiffness is related to deterioration and/or wear. I completely reconditioned my clutch system (from the rubber pedal pad to the clutch disc and everything in...
  25. Thread: Clutch replace

    by DMC-81
    Replies
    176
    Views
    8,687

    [Transmission 5-Speed] Thanks Dennis. I decided to re-ask Castrol / BP...

    Thanks Dennis. I decided to re-ask Castrol / BP today and here was the quick response:

    Question:

    TO: contactus_at_bp_dot_com

    Hi There,

    I understand that the below product replaced the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4