FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    98
    Views
    2,282

    [General] Probably would work if just milling a mill or...

    Probably would work if just milling a mill or two. But the surface grinder would give the best finish and maybe lapped on a surface block.
    ...
  2. Replies
    98
    Views
    2,282

    [General] I wonder how the nozzles are held in. I would...

    I wonder how the nozzles are held in. I would think they have to be sealed real well so suspect they are glued in. I would guess the whole assembly is then surfaced on a surface grinder.
  3. Replies
    44
    Views
    1,052

    [Fuel] John Hervey passed away some time ago (he owned...

    John Hervey passed away some time ago (he owned Special T). Don't know if anyone else has taken over his business.

    It sounds like your FD needs a slight surface machining to even out the contact...
  4. Replies
    44
    Views
    1,052

    [Fuel] +1 I did test one unit that worked very poorly...

    +1

    I did test one unit that worked very poorly if you pressed the air plate all the way down but with less press it worked great. I don't know if all units do that since I've only flow tested two...
  5. Replies
    44
    Views
    1,052

    [Fuel] I think mine was cheaper than a stock one. I...

    I think mine was cheaper than a stock one. I would guess there were more of them on the market. I seem to remember Hervey sold them cheaper then his price for the stock one.
  6. Replies
    44
    Views
    1,052

    [Fuel] Here is the data plate on my adjustable FD. This...

    Here is the data plate on my adjustable FD. This unit has always been on my car so don't know if anyone has opened it. I did a very small adjustment on one or two of the ports.
  7. Replies
    14
    Views
    388

    [Transmission 5-Speed] Mine is modified. That last photo is a new part...

    Mine is modified. That last photo is a new part I machined which gets bolted tight onto the frame. I needed a larger surface area where it contacts the frame because of the damaged epoxy. So the...
  8. Replies
    14
    Views
    388

    [Transmission 5-Speed] The bolt should seat on the frame and therefor...

    The bolt should seat on the frame and therefor should be torqued tight. Mine the epoxy on the frame in that area was all gone and it had a lot of rust. I machined my pivot arm with a new bearing...
  9. Replies
    4
    Views
    241

    What pressure are you stating? Primary pressure...

    What pressure are you stating? Primary pressure should always be 75 PSI hot or cold. Control pressure starts out around 20 PSI cold and after warmup is running around 50 PSI.
  10. Replies
    44
    Views
    1,052

    [Fuel] There was a head gasket sealer that you sprayed...

    There was a head gasket sealer that you sprayed on back in the day. Not sure if they sell that anymore.
  11. Replies
    44
    Views
    1,052

    [Fuel] I one time considered doing this for others. I...

    I one time considered doing this for others. I did rebuild one and used the shellac sealer. I did not like that sealer or any sealer because the two half surfaces are so perfectly flat and when...
  12. Replies
    23
    Views
    698

    [Engine] OK. Now I see it with that last drawing. It was...

    OK. Now I see it with that last drawing. It was throwing me because the drawing was not representing what the PPR looks like. I knew the end of the PPR is a solid blocked fixture. It should have...
  13. Replies
    23
    Views
    698

    [Engine] Is there an open hole at the end of unit? If not...

    Is there an open hole at the end of unit? If not where does that vent to?
  14. Replies
    23
    Views
    698

    [Engine] I think the O-ring at the very end of the piston...

    I think the O-ring at the very end of the piston is what seals rest pressure. I don't see what the function of that internal O-ring does.
  15. Replies
    20
    Views
    452

    [Transmission 5-Speed] My car does not have the stop bolt for the...

    My car does not have the stop bolt for the clutch. It also has Robs adjustable link. Hence my clutch pedal does sit higher than the brake pedal. That does not bother me but I would guess I could...
  16. Cool idea.

    Cool idea.
  17. [Frame & Body] I looked it up on internet and one source shows...

    I looked it up on internet and one source shows these values which does show SS is a little heavier.

    304 SS 7.93 grams/cm3
    Cold rolled 7.87 grams/cm3

    If my math is correct that makes SS 0.76%...
  18. [Frame & Body] I'm pretty sure a block of stainless steel is a...

    I'm pretty sure a block of stainless steel is a little lighter than a block of cold rolled steel. Now you may need more SS to get the same strength which would make the frame weigh more. It drives...
  19. [Engine] I replaced all my coolant pipes a long time ago. ...

    I replaced all my coolant pipes a long time ago. There are a few stock pipes without the bead. Looks like they had to cut those shorter to fit. I've not had any leakage with my silicone hoses on...
  20. [Frame & Body] If they look seated, it may just be a few are...

    If they look seated, it may just be a few are shorter.
  21. Replies
    3
    Views
    250

    [Electrical] The new DMCH switches have been reliable. The...

    The new DMCH switches have been reliable. The are a little taller then the stock switches.
  22. Replies
    11
    Views
    603

    8.5 ma load is not to bad but still why would you...

    8.5 ma load is not to bad but still why would you want a remote to shut off the battery.
  23. Replies
    11
    Views
    603

    Well reduce the chance of a fire or risk not...

    Well reduce the chance of a fire or risk not being seen after an accident.
  24. Replies
    11
    Views
    603

    I did a design change to the OEM clock which...

    I did a design change to the OEM clock which dropped the standby current a lot. That was posted on the old DMCtalk so not sure if that info exits anymore.

    You can run a fused battery wire to...
  25. Replies
    11
    Views
    603

    I designed my remote battery cut off a long time...

    I designed my remote battery cut off a long time ago. It's nice to not have a switch mounted to the battery cover and easy to reach and place the push button to operate while sitting in the drivers...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4