FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    3
    Views
    51

    That would probably work but I would guess the...

    That would probably work but I would guess the gauge would read higher since our 80 PSI requires 76 ohms and this sender would be 90 ohms at 80 PSI.

    This was from an owner that wanted to drive the...
  2. Replies
    3
    Views
    51

    Oil pressure guage calibration

    I had a request from an owner to relate the resistance (from the oil sender) to each mark on the gauge.

    76 ohms = 80 PSI - 162 ma.
    63 ohms = 3/4 mark - 173 ma.
    43 ohms = 1/2 mark - 191 ma.
    26...
  3. Replies
    100
    Views
    5,370

    Relay footprint

    Here is a nice data sheet on relays. It has a lot more info than most which I why I keep it.
  4. Replies
    26
    Views
    1,258

    [Engine] Epoxy is not really made to work at engine block...

    Epoxy is not really made to work at engine block temperatures. But since others have had luck with it why not try. I'm not sure a welder could get a TIG torch into that tight location and make a...
  5. Replies
    100
    Views
    5,370

    I was just thinking maybe the PO had a bad...

    I was just thinking maybe the PO had a bad alternator that put out to much voltage. Is there a battery disconnect switch? It's very bad if the battery disconnects with the engine running.
  6. Replies
    100
    Views
    5,370

    It's rare the lambda ECU goes bad but it's...

    It's rare the lambda ECU goes bad but it's looking like that may be your problem. Another common problem is the two grounds for the lambda come through the bulkhead and have to get connected to the...
  7. Replies
    100
    Views
    5,370

    Make sure all 5 pins on the lambda relay socket...

    Make sure all 5 pins on the lambda relay socket are seated.

    I don't know what that other Bosch relay would be for but most likely is just a standard relay.
  8. Replies
    100
    Views
    5,370

    A standard relay has pin 87a connected to pin 30...

    A standard relay has pin 87a connected to pin 30 just testing with an ohmmeter. The lambda relay will not be connected with those pins.

    The OEM lambda relay is a BOSCH 0332015012 12V 2x 15A
  9. Replies
    94
    Views
    5,047

    I made my new tool holder to machine the other...

    I made my new tool holder to machine the other side of the ball and it worked very good.

    I put the ball in my car without the 1/4" locking nut that is used to hold the ball in the correct...
  10. Replies
    100
    Views
    5,370

    The OEM lambda relay is a lower profile unit. ...

    The OEM lambda relay is a lower profile unit. Some relays show how the contacts are arranged with a schematic printed on the relay. A normal relay the center pin is normally connected to the power...
  11. Replies
    100
    Views
    5,370

    There is no reason a carb could not use the idle...

    There is no reason a carb could not use the idle system but I have not seen anyone do that yet. Not sure how well it would work.
  12. Replies
    100
    Views
    5,370

    ISM could be a bad connection or ECU may be bad....

    ISM could be a bad connection or ECU may be bad.

    Make sure your lambda relay is the proper type. That relay is not the same as all the other relays. A wrong one will stop the FV from buzzing.
  13. Replies
    100
    Views
    5,370

    That statement that the idle system is only...

    That statement that the idle system is only operational when the idle switch is closed is not true. Pull a wire off the switch and start up your cold engine and see that nothing changes in the...
  14. [General] I agree. But it will take some time to get the...

    I agree. But it will take some time to get the 600 miles on a tank with my Toyota Camry.
  15. Replies
    100
    Views
    5,370

    As far as I know pressing the idle switch does...

    As far as I know pressing the idle switch does nothing to the idle ECU or idle motor. It should add the vacuum advance on a warm engine and you should hear or see that change the idle for a moment. ...
  16. Replies
    94
    Views
    5,047

    For you guys that like machining. Here it is set...

    For you guys that like machining. Here it is set up in my lathe and the half ball machined. I should get my blank tool in a few days so I can make that tool and machine the other half.
  17. Replies
    94
    Views
    5,047

    Here are a couple photos of the Gear ball before...

    Here are a couple photos of the Gear ball before machining. I have poured the white epoxy into the top box which fills the "decal" and gives me something strong to clamp to in my lathe. I also...
  18. Replies
    94
    Views
    5,047

    Yes the examples of what can be done by an...

    Yes the examples of what can be done by an experienced machinist is amazing. I have had my Sherline machines for over 20 years and they still sell the same machines today.
  19. Replies
    94
    Views
    5,047

    I have the Sherline lathe and mill along with a...

    I have the Sherline lathe and mill along with a lot of their accessories. Maybe someday I will update them the CNC.

    https://www.sherline.com/
  20. Replies
    94
    Views
    5,047

    I had a great idea while machining the last gear...

    I had a great idea while machining the last gear ball I just printed. I am having trouble getting the second half of the ball machined because of the accuracy of the threaded insert pressed and...
  21. Replies
    94
    Views
    5,047

    Well I'm keeping the 15 degree offset on the...

    Well I'm keeping the 15 degree offset on the "decal" so all I'm doing now is making changes to make machining changes to my 3D model. I put two rings on the ball so I can center it with my dial...
  22. Replies
    100
    Views
    5,370

    Yes they just slid off but OEM ones are pretty...

    Yes they just slid off but OEM ones are pretty hard to slid off. I just cut them.
  23. Replies
    35
    Views
    1,081

    I'm at 13 years. I think owners that work on...

    I'm at 13 years. I think owners that work on their own car tend to keep them longer. Fixing things tends to add to owner enjoyment.
  24. Replies
    94
    Views
    5,047

    Well I printed a ball with the lettering pointing...

    Well I printed a ball with the lettering pointing down (this is the last thing printed and is away from the base, my printer the base is on top and it moves down to start and then moves up with each...
  25. Replies
    94
    Views
    5,047

    That may be a good idea on some designs but my...

    That may be a good idea on some designs but my problem was I could not wash the uncured resin out of the fine lettering outline.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4