FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DMC-Ron

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    2,117

    full scale flying (soon) styrofoam DeLorean

    https://youtu.be/vXDUZpdSU_A?si=mgG6p9yQQk_DS1Kt
  2. Replies
    9
    Views
    2,472

    [Electrical] Headlight load is handled by the two relays (main...

    Headlight load is handled by the two relays (main beam relay and dip beam relay) so their current does not go through the switch contacts. However, current for all the other running lights does go...
  3. Replies
    27
    Views
    3,776

    [General] Fair enough.

    Fair enough.
  4. Replies
    27
    Views
    3,776

    [General] Tough Crowd.

    Tough Crowd.
  5. Replies
    86
    Views
    79,815

    [General] Mike, There's a subtle difference. In the photo...

    Mike,
    There's a subtle difference. In the photo on this thread, the blue/yellow wire (wire has been spliced and extended with a brownish wire) is connected with the white/red on the solenoid coil...
  6. Replies
    11
    Views
    1,049

    [Electrical] See attached diagram. Low Beam is relay 21. ...

    See attached diagram. Low Beam is relay 21. Fuse for low beam is number 14
    Ron

    69951
  7. Replies
    8
    Views
    1,616

    [Electrical] Mike, Your measurement is likely correct. There...

    Mike,
    Your measurement is likely correct. There are differences between different manufacturers on how they handle high/low beam. But one method used involves a slightly offset placement of LED...
  8. [Electrical] Lars, Normally the "low beam" indicator in the...

    Lars,
    Normally the "low beam" indicator in the binnacle is directly powered from the low beam (dip) headlight relay circuit; meaning it gets the same power feed as the headlights. If the headlights...
  9. Replies
    14
    Views
    5,153

    [Frame & Body] Before drilling, I would suggest you first try...

    Before drilling, I would suggest you first try using an 8-32 tap and see if you can rejuvenate the threads in the nutserts.
    Ron
  10. Replies
    22
    Views
    3,163

    [Engine] Perhaps a transition beyond the valley would be...

    Perhaps a transition beyond the valley would be prudent?
  11. Replies
    14
    Views
    2,581

    [Electrical] Andy, Having your battery voltage, settle to...

    Andy,
    Having your battery voltage, settle to 12.5 volts after the engine turns off is pretty normal. If it sets for a few hours, it's not uncommon for the battery voltage to drop to 12.2 or so. ...
  12. Replies
    14
    Views
    2,581

    [Electrical] Andy, I think both Nick and Dave are onto...

    Andy,
    I think both Nick and Dave are onto something. To assist, I?ve annotated a schematic with the 3 likely scenarios. If, in fact, the smaller gauge brown wire is connected to the two larger...
  13. Andy, What is the exact part number for the...

    Andy,
    What is the exact part number for the Bosch plugs. Do you happen to have a purchase link?
    Ron
  14. Replies
    15
    Views
    3,147

    [General] What AGM manufacture and model did you choose? I...

    What AGM manufacture and model did you choose? I also have an old Interstate battery that's still working at 7 years but thinking about AGM.
    Ron
  15. Replies
    23
    Views
    3,308

    [Frame & Body] Dave, Those look good! If it turns out they...

    Dave,
    Those look good! If it turns out they wear through quickly and you're looking for another solution, perhaps modifying chair or cane silicone tips might be an option. There are small diameter...
  16. Replies
    60
    Views
    5,272

    [Transmission Auto] Dave, Maybe you have already checked this. ...

    Dave,
    Maybe you have already checked this. After cranking pull a couple of plugs and see if they are wet or dry. Knowing if it's flooding, or starved ,helps focus the troubleshooting.

    Ron
  17. [Electrical] Owners often disconnect the wire from the second...

    Owners often disconnect the wire from the second LH door plunger switch to stop the annunciator from buzzing when the door is open. The buzzer is obnoxious. The first plunger switch handles the...
  18. Replies
    6
    Views
    1,218

    [Electrical] Dan, Usually a weakening magnet will not...

    Dan,
    Usually a weakening magnet will not suddenly cause the speedo needle to not move. All speedo magnets slowly lose their magnetism over time. This usually results in the speedometer reading...
  19. [General] Just Googled DeLorean Parts Northwest and they...

    Just Googled DeLorean Parts Northwest and they did not show up. Only the real DPNW.
  20. Thread: Idle hunt

    by DMC-Ron
    Replies
    108
    Views
    12,062

    [Engine] Dave, Would it be possible to add a plug for a...

    Dave,
    Would it be possible to add a plug for a remote LED? Then we could have an indicator on an extension cord that we could see when working in the engine compartment.
    Ron
  21. [Engine] Lars, Consider doing a temperature test before...

    Lars,
    Consider doing a temperature test before installing the sensor. This is similar to what you might do when checking a thermostat. If you have a portable hot plate, pot with water, and...
  22. Replies
    32
    Views
    3,948

    I"m very pleased with this one. It's small and...

    I"m very pleased with this one. It's small and reads DC down to milliamps.
    Ron

    https://www.amazon.com/gp/product/B00O1Q2HOQ/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1

    69262
  23. [Electrical] Magnus, I know you hear a relay (or relays)...

    Magnus,
    I know you hear a relay (or relays) clicking, but as a simple check, I suggest you see if the start relay is clicking. Just put your hand on the relay while someone turns the ignition key...
  24. Thread: Idle hunt

    by DMC-Ron
    Replies
    108
    Views
    12,062

    [Engine] Or, if you want to test on a totally original set...

    Or, if you want to test on a totally original set up, I'm happy to volunteer.

    Ron
  25. Replies
    490
    Views
    313,595

    Domi, If that 11.6 volts was measured with both...

    Domi,
    If that 11.6 volts was measured with both old taillight boards in place and the incandescent brake bulbs glowing, then that is a good result. If it was measured without the boards and bulbs,...
Results 1 to 25 of 446
Page 1 of 18 1 2 3 4