FRAMING JOHN DELOREAN - AT THEATERS THIS WEEKEND & ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. [Heat & A/C] The Vendors low power fans seem to run between 7...

    The Vendors low power fans seem to run between 7 to 9 amps each. I've tested a few OEM fans that run about 14 amps each but even those are ones that have burned up the fan fail socket and jumpers. ...
  2. +1 With no fans running and the AC on the high...

    +1
    With no fans running and the AC on the high pressure goes really high.
  3. Pull the diode that has the pink wire on it. No...

    Pull the diode that has the pink wire on it. No fans when the AC is on will probably blow an AC hose.
  4. Replies
    3
    Views
    156

    [Engine] There are two pins on the blue bulkhead that go...

    There are two pins on the blue bulkhead that go directly to two pins of the lambda ECU. So pulling the blue connector removes the lambda ECU grounds and will change the mixture.
  5. [Heat & A/C] I checked my blower currents putting the current...

    I checked my blower currents putting the current clamp over the blower wire only, at the blower location. Engine was idling and my idle voltage is 14.6 volts. Room temp is 78 deg. F and mode switch...
  6. [Heat & A/C] Those seem like rally low currents from what I...

    Those seem like rally low currents from what I remember testing my blower. Did you check them with the engine running? I will check mine again.

    The blower breaker should have 4 wires with the...
  7. [Heat & A/C] I hope it does DC current. A lot of the cheap...

    I hope it does DC current. A lot of the cheap ones only work with AC current.
  8. [Heat & A/C] I don't have this meter but from the description...

    I don't have this meter but from the description it does look like it will read DC current and is not very expensive.
    ...
  9. [Heat & A/C] Most mutimeter amp limit is 10 amps. Many even...

    Most mutimeter amp limit is 10 amps. Many even fuse that range. Your going to pull much more than 10 amps.
  10. [Heat & A/C] You would need to measure the fan current on...

    You would need to measure the fan current on speed 4 to determine if the fan or circuit breaker is bad. It may just be you have a bad breaker. To measure the current you would probably need a clamp...
  11. Replies
    33
    Views
    1,223

    [General] When I saw the ads for the DeLorean in car...

    When I saw the ads for the DeLorean in car magazines in the late 70s I said right there I would own one someday. Thirty five years later it was possible for me to buy one since my kids were out of...
  12. Replies
    7,963
    Views
    1,243,892

    [General] Another thing I think is a good thing with EFI is...

    Another thing I think is a good thing with EFI is the fuel accumulator. It removes the pulses you get from the fuel pump. If you ever run a pressure washer and that hose touches your body, you...
  13. Replies
    7,963
    Views
    1,243,892

    [General] I ran a few errands the past two days with the D...

    I ran a few errands the past two days with the D and did not note any skipping. I'm thinking it may just have been not driving my D for a long time maybe an injector or something else in the fuel...
  14. Replies
    7,963
    Views
    1,243,892

    [General] A few nice things with my idea of no return fuel...

    A few nice things with my idea of no return fuel line.

    1) The fuel in the tank should stay cooler if your still running K-jet. Not so much with EFI unless the return line is after the injector...
  15. Replies
    7,963
    Views
    1,243,892

    [General] It still takes someone capable of understanding...

    It still takes someone capable of understanding how it all works and has good mechanical and electrical experience. But you guys got me thinking. So do you pressure regulate your fuel supply by a...
  16. Replies
    7,963
    Views
    1,243,892

    [General] Maybe someday I will change to EFI. My K-jet...

    Maybe someday I will change to EFI. My K-jet never gave me problems for 10 years. This is my first problem.
  17. Replies
    7,963
    Views
    1,243,892

    [General] I resistance checked the old wires. Shortest one...

    I resistance checked the old wires. Shortest one was 700 ohms, longest was 1200 ohms, others were between.

    I updated the software in my wideband LM2 and retested the tail pipe AFR. Still the AFR...
  18. Replies
    9
    Views
    320

    [Heat & A/C] Installed the new set of ignition wires. Not...

    Installed the new set of ignition wires. Not sure if that fixed it but a quick drive around the neighborhood I did not note a skip under load. I will need to do a longer drive later.

    The tail...
  19. Replies
    7,963
    Views
    1,243,892

    [General] That's what I should have tried first. No Since...

    That's what I should have tried first. No Since I have new wires coming in I will change them all. If those fix it I will ohm the wires just to make sure.
  20. Replies
    7,963
    Views
    1,243,892

    [General] Ran an injector spray test (six bottles and pump...

    Ran an injector spray test (six bottles and pump running, press the air plate) and all six look very good with very even amount of flow.

    I really thought this was going to show it was my skipping...
  21. Replies
    4
    Views
    185

    [Electrical] The EU guys have to have headlights that are...

    The EU guys have to have headlights that are approved to pass their MOT testing and most of those are 50 watts or more. So that is why they up the fuse that gets hot with the headlights. They have...
  22. Replies
    27
    Views
    1,311

    [General] The fuel pump fuse has popped with one owner...

    The fuel pump fuse has popped with one owner because his frequency valve shorted. Another common problem is the WUR heater shorts but often that does not pop the fuse mostly because the wiring to it...
  23. Replies
    7,963
    Views
    1,243,892

    [General] Installed the narrow band O2 sensor to replace my...

    Installed the narrow band O2 sensor to replace my wideband unit. Had to adjust the dwell a little. Tail pipe AFR check showed around 16.5 AFR and an occasional jumping around. So took the car for...
  24. [Engine] The correct sender is very critical to have the...

    The correct sender is very critical to have the gauge read correctly. I did some sender testing and I did get three senders reading the same. The gauge like most old automotive gauges compensate...
  25. [Engine] That is pretty much what the OEM unit does. It...

    That is pretty much what the OEM unit does. It does not have much in the way of dwell optimization. The distributor coil just generates an AC voltage with the zero crossing coinciding to the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4