My engine block had some corrosion like that on one cylinder, but not quite so bad. A local machine shop repaired it with some sort of epoxy, using a cylinder liner to shape it. I'm not quite sure...
Type: Posts; User: Jason
My engine block had some corrosion like that on one cylinder, but not quite so bad. A local machine shop repaired it with some sort of epoxy, using a cylinder liner to shape it. I'm not quite sure...
What's the total approximate cost in parts (engine, ecu, exhaust, other bits, but no turbo) for a conversion like this?
On the "new" door, the holes for attaching the crossmember (108319) are significantly smaller, and the screws don't fit. And one of the holes in the middle is missing. Is this normal? Are you...
New door is on the car. I now have to install all the door interior bits. But while I was reinstalling the torsion bar it occurred to me....
Ever since I replaced the front door hinge years ago...
My door replacement project has turned into a roof box repair project. Who could have guessed?
The roof box has some rust but appears to be structurally sound. I was thinking of cutting a large...
No. That piece I'm leaving attached to the fixed glass. I'm talking about how the fixed glass is attached to the door.
I got the fixed glass out. Turns out I didn't need any special tools. It appears that when the glass was installed it was put into position, a few metal tabs were riveted to the door to hold the...
I'm starting the process of replacing my driver's side door. The "new" door is bare, just the door itself, so all the other parts need to be swapped over. I'm generally familiar with working inside...
Well, I screwed up and managed to smack the lower leading edge of my driver's side door against the bottom of the open garage door. The lower front corner is now bent in a little. The rest of the...
Autozone stocks this one
https://www.autozone.com/electrical-and-lighting/antenna/p/metra-antenna-pwant/220455_0_0
Silver instead of black mast, but it fits on the original power antenna mount...
Maybe check for exhaust gases in the coolant?
My car would behave similar to what you describe. Normal temps with the AC off, but with the AC on and over 80 degrees outside the coolant temp would...
My rear bearings made it 39 years and 230k miles before needing replacement. The fronts were replaced at least twice in the same period, but mostly because they split when the hubs were pulled to...
67845
Ignore the dirt. The car is a with children daily driver.
I used something like this..
https://www.ebay.com/itm/BLACK-STITCH-TOP-CENTER-CONSOLE-PAD-LEATHER-COVER-FITS-DELOREAN-DMC-12-81-83-/232027615386
I can't remember if I got it from this seller...
For me it's a time thing (I've got other projects going on now), and trying to minimize how long the car is off the road. I assume I could change out the rack in an evening. Getting all fiddly with...
The inner tie rod ends on my steering rack are a bit loose. Looking at the cost of new racks from DMCH and Delorean Go it seems like it's worth the time/hassle savings to just get a new rack rather...
I'm not sure if this will work for your particular hole, but when I found a hole in the side of my block I did...
...
I guess I'm just tired of having to take it to the shop. I generally find it more convenient to mess about with things in the evening then work out the logistics of getting the car to and from the...
Would you be willing to share the details of your strings fixture and the 3d models?
Does anyone have any ideas/suggestions/tips on how to do a 4 wheel alignment at home?
I've got one of these http://www.trackace.co.uk/ which does an ok job of measuring the angle between wheels,...
If you really aren't get any dye showing at any of the places you mentioned, the only thing left is the evaporator.
You can try looking into the evaporator box through where the blower motor or...
Doesn't the DPI exhaust come with two fittings for O2 sensors? I have separate wide and narrow band sensors in mine and didn't have to weld anything.
If by flywheel inspection plate you mean part 101073, I would just leave it off. All it seems to do is make it hard to remove the transmission. When the engine and transmission are in the car its...
Years ago, when I had my car at a local shop to fix an exhaust manifold leak they found the same thing with my cat. At the time they hollowed it out and put it back with the plan that I would source...
I just increased the idle speed a bit. Which also helps with AC while sitting in traffic.