FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DMC-81

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    8,455
    Views
    1,571,936

    [General] Lol! If your DeLorean's horn sounds like any...

    Lol! If your DeLorean's horn sounds like any dying animal, it's time to replace both and check the wiring and ground. I replaced both mine with the original Mixo units from DMC when I restored the...
  2. Replies
    54
    Views
    12,539

    Wow, you're right....great video. Thanks for...

    Wow, you're right....great video. Thanks for sharing.
  3. Replies
    45
    Views
    4,110

    Great progress so far! :thumbup:

    Great progress so far! :thumbup:
  4. Replies
    6
    Views
    282

    [Engine] Yes, I would find a slightly larger o-ring. It...

    Yes, I would find a slightly larger o-ring. It should fit snug.
  5. [General] I found that I needed 28 ft/lbs to properly crush...

    I found that I needed 28 ft/lbs to properly crush the washer and provide a leak free installation.

    More information here:...
  6. Replies
    14
    Views
    1,462

    [General] Very cool product. :thumbup:

    Very cool product. :thumbup:
  7. Replies
    1
    Views
    572

    No tips. I would contact the vendor.

    No tips. I would contact the vendor.
  8. I think the Renault Alpine is okay, but it...

    I think the Renault Alpine is okay, but it reminds me of the Fuego. I can think of other 1985 cars that I would rather have.

    Otherwise, I agree with what has been said so far. In addition the car...
  9. Replies
    12
    Views
    584

    [General] One thing to be aware when putting this list...

    One thing to be aware when putting this list together is the strength of a given bolt. It is marked on the head. While stainless steel looks great, it is not a high strength material. I would take...
  10. Replies
    8
    Views
    451

    [Frame & Body] I would recommend having a good/ reputable body...

    I would recommend having a good/ reputable body shop paint the fascias. I used the correct DMC paint code and it turned out well. That was 5 years ago, and they held up well. I think it was around...
  11. +1. Also use a soft pillow to put under your...

    +1. Also use a soft pillow to put under your knees as you will be on them for a while, leaning over the fuse box.

    Do yourself a favor, get a quality crimping tool like this one from Grainger:...
  12. Replies
    18
    Views
    1,231

    [Brakes] Here is more discussion on the brake master...

    Here is more discussion on the brake master cylinders: http://dmctalk.org/showthread.php?16595-50-50-vs-38-62-brake-master-cylinder
  13. Replies
    355
    Views
    84,709

    Theme music salute

    So, I was fueling up the car today at WaWa where they have 89 octane non-ethanol gas. It is a recently built station with pumps that feature built in video screens and speakers. They were playing...
  14. Replies
    13
    Views
    750

    [Transmission 5-Speed] It left in 2013. Unfortunately, the owner passed...

    It left in 2013. Unfortunately, the owner passed away in 2008 in his 50s and the family brought it down to DMCFL 5 years later.
  15. Replies
    13
    Views
    750

    [Transmission 5-Speed] You are welcome. Interestingly, the original...

    You are welcome. Interestingly, the original owner of my car lived in Georgia and went to Georgia Tech. There was a "Ramblin' Wreck from Georgia Tech" sticker on the windshield when I bought the car.
  16. Replies
    3
    Views
    513

    [General] I found that by using my car in the Florida heat...

    I found that by using my car in the Florida heat meant that I couldn't cover the fuse box, nor keep the wooden relay compartment cover in place covered by the carpet.

    My solution was to make a...
  17. Replies
    13
    Views
    750

    [Transmission 5-Speed] Here are a couple pictures of the cross gate...

    Here are a couple pictures of the cross gate cable and other linkages attached to the gearbox:

    http://dmctalk.org/attachment.php?attachmentid=47677&d=1480994011
    ...
  18. Replies
    7
    Views
    630

    [Frame & Body] Hi Jonathan, Yes, they are aluminum. They are...

    Hi Jonathan,

    Yes, they are aluminum. They are not anodized. Mine were dirty as well. I cleaned the worst part of the grease, oil, and road tar off with engine degreaser and a non scratch cleaning...
  19. Replies
    31
    Views
    2,083

    [General] Yes. I completed my restoration under DMC's...

    Yes. I completed my restoration under DMC's Budget Restoration Program (BRP). Besides the discount, when I completed the car, I got a very nice framed certificate of completion and a handwritten...
  20. Thread: Oil leak help

    by DMC-81
    Replies
    3
    Views
    399

    [Engine] +1 on what Jonty said. Also, is it engine or...

    +1 on what Jonty said. Also, is it engine or transmission oil? The latter has a pungent sulfur smell to it.
    Based on where it is , engine oil can come from the rear main seal (the orange ring in the...
  21. Replies
    14
    Views
    2,407

    Sticky: I didn't know him, but knew he was a big part of...

    I didn't know him, but knew he was a big part of the DeLorean community. Condolences to his family and friends. May he rest in peace. :(
  22. Replies
    36
    Views
    2,398

    [Transmission 5-Speed] Is it a PRV engine?

    Is it a PRV engine?
  23. Replies
    23
    Views
    2,357

    [General] +1. Might as well add to the chorus. 2016 for me...

    +1. Might as well add to the chorus. 2016 for me too. I'm not sure if Rob changed suppliers, etc. since then, but you can call to verify and ensure stock.
    ...
  24. [Fuel] Also, try to only squeeze the pump trigger...

    Also, try to only squeeze the pump trigger halfway. This works for me. It is only a 14 gallon tank, so depending on how much fuel you have left, you can judge when to slow down by looking at how much...
  25. Replies
    9
    Views
    959

    [General] Hi. Yes CFI is correct. It was fixed with all new...

    Hi. Yes CFI is correct. It was fixed with all new door seals and then a striker pin adjustment.

    Funny enough, when I first went out to look at the car, the driver's door was stuck shut due to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4