Hey folks-I appear to have an antenna that is stuck in the raised position. I have disconnected all of the electrical connections, as I understood this to disconnect power to it. It will manually...
Type: Posts; User: rjd2
Hey folks-I appear to have an antenna that is stuck in the raised position. I have disconnected all of the electrical connections, as I understood this to disconnect power to it. It will manually...
just wanted to follow up and say that it was in fact the cap for the sending unit hole; because of the orientation of the hoses in the new GM style fuel pump, it's hard to get access to the cap(the...
Gotcha. Thanks. Yes, it's an integrated "GM style" unit from Delorean Industries, IIRC. maybe i should pull the internal shroud piece at the frunk and check the tank area.
Hi folks-so I have had DMC #2 on the road for a good chunk of 2023 after a fairly big recommissioning/restoration, and for the most part, all is well. Still some things I'm shaking out, but I have...
Hi folks-both of my Deloreans have non-working speedos. One of them intermittently worked with my reseating the plastic cap for the square drive at the spindle, but then went dead again. Is there a...
thanks folks. one of the first things i did to the car was to pull each fuse and check continuity. my voltage gauge has been behaving well, however the coolant temp situation is still not reading...
Finally getting some good seat time in on #5173 after what I would consider a full restoration, and I only have 2 outlier issues to get this car to "done".
1-if the car is cold, it fires...
Hi folks-so I removed the binnacle today on #5173 in an attempt to sort the coolant temp gauge. It reads, but at a fraction of what it should read. At it's hottest, it will read about 130, even when...
wish him the best of luck!!! decent chance he ends up here, eventually, i would guess. if he knows what's good for him! i got nervous when he backed the car onto a trailer, and then proceeded to...
WHEW!!! Ok, got it. Thanks to all for the advice!!! Going to detail my technique here for future documentation. I was able to get the window seated without removing the carriers(my rear nylon guide...
thanks for the help folks! well, I attacked this in the morning before there were all of these helpful comments. i was able to get the front drop window nylon guide into the carrier using a mirror....
Thanks(don?t see it in my inbox fyi)
Hi folks-replacing the drivers side window mirror. Have the old unit out, and the new unit in hand. I am struggling to seat the window in the guides, particularly the "front" guide(closest to front...
Thanks folks! After further investigation, it seems the DS window motor is shot. Ordered a new one, and have the door apart and old one out.
the bushing at the steering column/firewall was shot....
Hi folks, another D is on the road!!!! As previously stated, I worked a deal for a 6k mile 1982 one owner car that had sat since the fuel pump failed in 1993. I took the car on, and did:
all...
Blitzkreig'd it this morning, got it solved and installed. FYI the bearings can be reseated while packed with grease, it's just enormously messy
welp, popped a cap off one. sure enough, i installed all the races in the wrong channel. sigh...
ok, thanks folks. i'll pull the cap and see if I need to undo some of my work. appreciate it.
Hi folks-so, first time doing a CV axle rebuild on any car, so this may be just general ignorance or inexperience, but.... I rebuilt my CV axles, as the boots had failed. fully disassembled, cleaned,...
so does that mean I want a GL4 type oil? This is getting very confusing for me. It looks like GL5 is intended for hypoid gears. Most of the 85W90 gear oil I am finding is designated as "hypoid gear...
Hi all-I am restoring a DMC-12 that hasn't been on the road in 30 years. We JUST got the car running, and have not gotten it on the road yet. When I was doing all the heavy lifting aspects of the...
thanks! I was expecting a bolt sized recess, not a the big long "channel". I got it sorted today without having to unseat the steering rack, luckily.
Hi all-I replaced the steering rack on the car I'm restoring, and I got the joint seated between the column output shaft and the rack input shaft. I don't have the securing bolts set yet. I'm trying...
it can be done with standard issue spring compressors, but i have found that you have to get your placement EXACTLY right, both radius wise and coil wise. it has taken me several tries to get the...
I know this may sound corny-it sounds a little corny to me, frankly-but I periodically wonder about monetizing classic cars-Delorean being a great candidate-and wonder if anyone on here has explored...